Sony Handheld Game System PSP 2006 User Manual

EN  
CT  
Safety and Support  
安全與支援  
PSP-2006  
PSP-2007  
TM  
3-218-748-61(1)  
 
Table of contents  
About the PSP® system  
documentation  
The PSP® (PlayStation®Portable) system documentation includes the  
following:  
EN  
Safety and Support (this document)  
This document contains safety information related to the use of the  
PSP® system, troubleshooting, specifications and other information.  
Quick Reference  
This document contains information on basic hardware operations of  
the PSP® system.  
User's Guide  
(http://manuals.playstation.net/document/)  
This online document is accessed through the Internet and contains  
detailed information related to use of the PSP® system software.  
Information about system functionality published in this document  
may vary from the information for your PSP® system, depending on  
the system software version in use.  
Table of contents  
3
 
   
Before use  
Use and handling  
Use in a well-lit area and keep the screen a safe distance from your  
face.  
Precautions  
Avoid prolonged use of the PSP® system. To help prevent eyestrain,  
take a break of about 15 minutes during every hour of play.  
If you experience any of the following health problems, discontinue  
use of the system immediately. If symptoms persist, consult with  
your physician.  
Before using this product, carefully read this manual and retain it for  
future reference.  
Accessory compatibility  
The accessories that are supported by this system may differ  
from those of the PSP-1000 series PSP® system. For detailed  
– Dizziness, nausea, fatigue or symptoms similar to motion sickness  
– Discomfort or pain in a part of the body, such as eyes, ears, hands  
or arms  
Exercise care when setting the volume. If you set the volume too  
high, it may harm your hearing or damage the speakers.  
Keep the system and accessories out of the reach of small children.  
Small children may swallow the Memory Stick Duo™ or wrap the  
cables/straps around themselves, which may inflict injury or cause  
an accident or a malfunction.  
Do not use the system while driving or riding a bicycle. Looking at  
the screen or operating the system while driving an automobile or  
riding a bicycle may result in a traffic accident.  
Take extra care when using the system while walking.  
Be careful not to pinch your fingers when closing the disc cover.  
Do not use the system or accessories near water.  
Use only attachments/accessories specified by the manufacturer.  
Do not use the headphones if they cause discomfort to your skin.  
If the headphones cause discomfort to your skin, discontinue use  
immediately. If symptoms do not subside even after discontinuing  
use, seek medical attention.  
Do not expose the system or accessories to high temperatures, high  
humidity, or direct sunlight.  
Do not leave the system or accessories in a car with the windows  
closed (particularly in summer).  
Safety  
This product has been designed with the highest concern for safety.  
However, any electrical device, if used improperly, has the potential for  
causing fire, electrical shock or personal injury. To help ensure  
accident-free operation, follow these guidelines:  
Observe all warnings, precautions and instructions.  
Regularly inspect the AC adaptor and AC power cord for damage  
and for dust build-up around the mains power plug or electrical  
outlet.  
Stop use, unplug the AC power cord from the electrical outlet and  
disconnect any other cables immediately if the device functions in an  
abnormal manner, produces unusual sounds or smells or becomes  
too hot to touch.  
Call the PSP® service line at the number listed on your warranty card  
if the device does not operate properly.  
Do not expose the system or accessories to dust, smoke or steam.  
Precautions  
4
 
     
Do not allow liquid or small particles to get into the system or  
accessories.  
Do not place the system or accessories on surfaces that are tilted,  
unstable or subject to vibration.  
Do not throw, drop or step on the system or accessories, and do not  
subject the devices to strong physical shock. Sitting down with the  
PSP® system in a pocket or placing the system in the bottom of a  
backpack along with heavy objects may cause damage to the system.  
Do not forcibly twist the PSP® system or expose the system to strong  
physical shock during gameplay, as doing so can damage the system  
or cause the disc cover to open, ejecting the disc. Handle the analog  
stick with care.  
Do not put heavy objects on the system or accessories.  
Do not touch or insert foreign objects into the connectors of the  
system or accessories.  
Do not place the system close to items with a magnetic strip, such as  
credit cards.  
Do not touch the system or AC adaptor for an extended period of  
time while in use. Depending on the conditions of use, the system or  
AC adaptor may reach temperatures of 40°C/104°F or more.  
Extended contact under these conditions may cause low-temperature  
burns*.  
AC adaptor and AC power cord use  
Do not touch the mains power plug of the AC power cord with wet  
hands.  
Do not touch the AC power cord, AC adaptor or the system, if  
connected to an electrical outlet, during an electrical storm.  
Do not use a power source other than the supplied (or approved  
replacement) battery pack, AC adaptor and AC power cord.  
Do not allow dust or foreign matter to build up around the system or  
accessory connectors. If there is dust or foreign matter on the  
system's connectors or the AC power cord, wipe it off with a dry  
cloth before connecting. Dust or other matter on the connectors can  
result in fire or electrical shock.  
Unplug the AC power cord from the electrical outlet, disconnect any  
other cables and remove the battery pack from the system before  
cleaning or when you do not intend to use the system for an extended  
period of time.  
Protect the AC power cord from being walked on or pinched  
particularly at plugs, convenience receptacles and the point where  
they exit from the system.  
When disconnecting the AC power cord, hold it by the plug and pull  
straight out from the electrical socket. Never pull by the cord and do  
not pull at an angle.  
EN  
*
Low-temperature burns are burns that occur when the skin is in contact  
with objects of relatively low temperatures (40°C or more/104°F or  
more) for an extended period of time.  
Do not use the system to play games or video when the system is  
covered with any type of fabric. If you want to pause or temporarily  
store the system while playing games or video, put the system in  
sleep mode before placing it in the case or covering. Also do not use  
the AC adaptor when covered with fabric. This may help to avoid  
overheating.  
When connecting the system to a plasma or projection* TV, do not  
leave a still image on the TV screen for an extended period of time,  
as this may leave a faint image permanently on the screen.  
*
Except LCD screen types  
Do not connect the AC power cord to a voltage transformer or  
inverter. Connecting the AC power cord to a voltage transformer for  
overseas travel or an inverter for use in an automobile may cause  
heat to build up in the AC adaptor and may cause burns or a  
malfunction.  
Precautions  
5
 
The socket-outlet shall be installed near the equipment and shall be  
easily accessible.  
About the "pickup"  
Do not touch the "pickup" located inside the disc cover of the system.  
Touching the pickup may damage the system.  
LCD screen  
The LCD screen is made of glass and may crack if subjected to  
excessive force.  
Black (dark) pixels and continuously lit pixels may appear in certain  
locations on the LCD screen. The appearance of such spots is a  
normal occurrence associated with LCD screens and is not a sign of  
a system malfunction. LCD screens are made using highly precise  
technology. However, a very small number of dark pixels or  
continuously lit pixels exist on each screen. Also, a distorted image  
may remain on the screen for several seconds after the system has  
been turned off.  
Pickup  
Direct exposure to sunlight may damage the system's LCD screen.  
Be careful when using the system outdoors or near a window.  
When using the system in a cold environment, you may notice  
shadows on the graphics or the screen may appear darker than usual.  
This is not a malfunction, and the screen will return to normal when  
the temperature goes up.  
Memory Stick Duo™  
For best results, follow these guidelines:  
Do not leave still images displayed on the screen for an extended  
period of time. This may cause a faint image to be left permanently  
on the screen.  
Do not touch the connector area (A) with your hands or with metal  
objects.  
Do not press hard when writing on the memo area (B).  
Do not use or store a Memory Stick Duo™ in the following:  
– Places subject to high temperatures, such as in a hot vehicle  
– Locations exposed to direct sunlight  
– Locations that are very humid or conducive to corrosion  
Precautions  
6
 
When using Memory Stick Duo™ media without an erasure  
prevention switch, take care not to overwrite or delete data by  
accident. If your Memory Stick Duo™ media has an erasure  
prevention switch, you can prevent data from being saved, edited, or  
deleted by setting the switch in the LOCK position.  
in a case or covering may cause overheating or may damage the  
system.  
Put both the PSP® system and the remote control in hold mode to  
help prevent unintended operation.  
Never disassemble the system or  
accessories  
Recorded data  
Do not use the Memory Stick Duo™ in the following ways, as doing  
so may result in data loss or corruption:  
EN  
Use the PSP® system and accessories according to the instructions in this  
manual. No authorization for the analysis or modification of the system,  
or the analysis and use of its circuit configurations, is provided.  
Disassembling will void the systemwarranty. Additionally, there is a risk  
of fire, electrical shock or malfunction. The LCD screen, in particular,  
contains dangerous, high-voltage parts, and the laser beam for reading  
UMD™ may cause visual impairment if exposed directly to the eyes.  
Removing the Memory Stick Duo™ or turning off the system while  
it is loading or saving data or being formatted.  
Using it in a location that is exposed to static electricity or electrical  
interference.  
If, for any reason, software or data loss or corruption occurs,  
it is usually not possible to recover the software or data. It is  
recommended that you regularly back up software and data.  
Sony Computer Entertainment Inc. and its subsidiaries and  
affiliates will not be held liable for any damages or injury in  
the case of software or data loss or corruption.  
Using the access point  
When using the PSP® system's 'Scan' function to select a wireless LAN  
access point, access points that are not intended for public use may be  
displayed. Only connect to a personal access point that you are  
authorized to use, or one that is available through a public wireless  
LAN or hotspot service.  
In accordance with copyright law, no recorded data may be  
used for purposes other than personal enjoyment without  
permission from the copyright holder.  
Overseas use  
Depending on the country, there are limitations on the use of certain  
types of radio waves. In some cases, use of the system may lead to a  
fine or other penalty.  
Cases and coverings  
When placing the PSP® system in a commercially available case,  
turn off the power or put the system in sleep mode. Do not use the  
system while it is in the case. Leaving the system on, or using it while  
Precautions  
7
 
Do not use a chemically-treated cleaning cloth to wipe off the  
system.  
Moisture condensation  
If the PSP® system or UMD™ is brought directly from a cold location  
to a warm one, moisture may condense on the lens inside the system or  
on the UMD™. Should this occur, the system may not operate  
properly. In this case, remove the UMD™ and turn off and unplug the  
system. Do not put the UMD™ back in until the moisture evaporates  
(this may take several hours). If the system still does not operate  
properly, contact the PSP® service line at the number listed on your  
warranty card for assistance.  
Before using the analog stick  
For best results, go to  
(Settings)  
(System Settings) and  
then with the "System Information" screen displayed, rotate the analog  
stick in a circular motion. This will adjust the analog stick's range of  
movement.  
Cleaning  
UMD™ handling  
For safety reasons, unplug the AC power cord from the electrical outlet,  
disconnect any other cables and remove the battery pack from the  
system before cleaning.  
Do not touch the opening on the rear of the disc (recorded surface of  
the disc) with your fingers.  
Do not allow dust, sand, foreign objects or other types of dirt to get  
on the disc.  
If the UMD™ becomes dirty, gently wipe the exterior and recorded  
surfaces of the UMD™ using a soft cloth. Do not use solvents or  
other chemicals.  
Cleaning the exterior surface and LCD screen  
Wipe gently with a soft cloth.  
Do not use a UMD™ that is cracked or warped or has been repaired.  
The UMD™ may break inside the PSP® system, leading to injury or  
malfunction.  
Cleaning the connectors  
Do not use when the connectors of the system, AC adaptor or the AC  
power cord are not clean. Remove the dirt with a dry cloth or cotton  
swab. If used when dirty, the flow of electrical current may be  
obstructed.  
Handling and care of exterior surfaces  
If the headphones or remote control connectors become dirty, this  
could cause noise or interruptions in sound. Wipe the connectors  
with a dry, soft cloth to keep in clean condition.  
Follow the guidelines listed below to help avoid deterioration or  
discoloration of the PSP® system:  
Do not use solvents or other chemicals to clean the exterior surface.  
Do not allow the system to remain in direct contact with rubber or  
vinyl products for an extended period of time.  
Precautions  
8
 
Do not throw or drop the battery pack or subject it to strong physical  
shock.  
About the battery  
Do not put heavy objects on or apply pressure to the battery pack.  
Do not allow the battery pack to come into contact with liquids. If it  
becomes wet, discontinue use until it is completely dry.  
Keep the battery pack out of the reach of small children.  
If the PSP® system will not be used for an extended period of time,  
remove the battery pack and store it in a cool, dry place out of the  
reach of children.  
Battery pack precautions  
Warnings  
Use only the supplied battery pack or a replacement marked for use  
with the correct model of the PSP® system.  
EN  
Do not handle a damaged or leaking battery pack.  
Contact with the material can result in injury or burns to the eyes or  
skin. Even if foreign substances are not immediately visible, chemical  
changes in the material can result in injuries occurring at a later time.  
Charging  
If you come into contact with material from a leaking battery  
pack, take the following actions:  
You can charge the battery using the AC adaptor or a USB cable (sold  
separately). For details about how to charge the battery, refer to the  
supplied Quick Reference manual.  
If the material gets into the eyes, do not rub. Immediately flush  
the eyes with clean water and seek medical attention.  
If the material comes into contact with the skin or clothes,  
immediately rinse the affected area with clean water. Consult  
your physician if inflammation or soreness develops.  
Estimating the battery charge time  
Charging with the AC adaptor  
Charging using a USB cable  
Approximately 2 hours 20 minutes  
Approximately 5 hours  
Handle the battery pack with care.  
The battery pack may explode or present a fire or chemical burn hazard  
if it is not handled carefully.  
Figures shown are for when charging a battery with no charge remaining.  
Do not allow the battery pack to come into contact with fire or  
subject it to extreme temperatures such as in direct sunlight, in a  
vehicle exposed to the sun or near a heat source.  
Do not cause the battery pack to short-circuit.  
Hints  
Do not use the PSP® system with the AC adaptor when the battery pack is  
not inserted in the system. If the AC adaptor is disconnected suddenly, it  
may result in damage to the system.  
Do not disassemble or tamper with the battery pack.  
Prevent damage to the battery pack. Do not carry or store the battery  
pack with metal items such as coins or keys. If damaged, discontinue  
use.  
Charge in a temperature of 10°C to 30°C/50°F to 86°F. Charging may not  
be as effective in other environments.  
Charging may take longer when the system is turned on during charging or  
when a USB cable is used for charging.  
About the battery  
9
 
   
USB charging uses the power supply of the USB port of the connected  
device. Charge the battery by connecting the PSP® system to a device  
equipped with a high-power USB port. If a low-power USB port or a USB  
hub is used, the battery may not be able to be charged.  
The battery pack lifespan varies depending on how it is stored, the  
conditions of use and environmental factors, such as temperature.  
When the AC adaptor and a USB cable are connected to the PSP® system,  
the battery is charged by the power supply of the AC adaptor.  
Do not use or charge the PSP® system with the battery cover removed. If  
the battery is suddenly removed, the battery may be dropped and damaged,  
which may cause a system malfunction.  
Replacing the battery pack  
For safety reasons, turn off the system and remove the power cord  
from the electrical outlet and disconnect any other cables before  
replacing the battery pack.  
If the system is left unused after the battery charge runs out or the  
battery pack has been removed, the date and time settings may be  
reset. If this occurs, the date and time setting screen will be displayed  
the next time the PSP® system is turned on.  
Estimated battery duration  
*1  
Game  
Approximately 3 - 6 hours  
Approximately 3 - 5 hours  
*2  
Video playback  
Storing the battery pack  
When the system will not be used for an extended period of time,  
remove the battery pack from the system. Store the battery pack in a  
cool, dry place out of the reach of children.  
*1 Based on tests conducted using the supplied battery pack, with the system  
in single player mode, with headphones with remote control in use, and  
with wireless LAN not in use.  
*2 Based on tests conducted using variables of system speakers versus  
headphones, volume level and screen brightness level.  
Hint  
Battery duration may vary depending on the type of content being played or  
usage conditions such as screen brightness and environmental factors. As the  
battery pack ages, it will have a shorter duration.  
Battery pack life  
The battery pack has a limited lifespan. Battery duration will  
decrease with repeated usage and age. If the battery duration  
becomes extremely short, it may be time to replace the battery pack.  
About the battery  
10  
 
*3 To use Memory Stick Micro™ media, you must first insert it into an M2  
Duo-size adaptor. If the Memory Stick Micro™ is inserted directly into  
the system, it may not be able to be ejected.  
Compatible media  
Hints  
The media types listed below can be used on the PSP® system.  
Throughout this manual, the term "Memory Stick Duo™" is used to  
refer to all types of Memory Stick™ media in the table below.  
The standard-size Memory Stick™ cannot be used with the system.  
Performance of all Memory Stick™ media is not guaranteed.  
If a Memory Stick Duo™ is formatted in a device other than the PSP®  
system, such as a PC, it is possible that the system will not recognize it. If  
Type  
Logo  
this happens, go to  
(System Settings)  
"Format Memory Stick™"  
EN  
and re-format the Memory Stick Duo™.  
UMD™  
UMD™  
Memory Stick Duo™ (not  
MagicGate™-compatible)  
UMD™ contain a region code that is assigned to each sales region.  
This system can play UMD™ marked with either region code "ALL"  
or "3".  
MagicGate™ Memory Stick  
Duo™  
*1  
Memory Stick Duo™  
*1 *2  
(MagicGate™ compatible)  
Memory Stick PRO Duo™  
Memory Stick PRO-HG  
Memory Stick™  
*1 *2  
Parallel data transfer (high-speed data transfer)  
Parallel data transfer is a high-speed data-transfer technology that  
allows multiple data input/output connectors on the Memory Stick™ to  
be used at the same time (parallel interface). The PSP® system supports  
4-bit parallel data transfer. However, the time required for reading/  
writing differs according to the media in use.  
*1 *2  
Duo™  
Memory Stick Micro™  
*1 *2 *3  
(M2™)  
*1 Compatible with MagicGate™  
*2 Compatible with high-speed data transfer over a parallel interface.  
Compatible media  
11  
 
   
File size limitation  
The specification of the file system used on Memory Stick™ media  
limits the size of files that can be recorded or played to less than 4 GB  
per file.  
MagicGate  
is a term of copyright-protection technology  
developed by Sony Corporation.  
Compatible media  
12  
 
,
Using the USB cable, the system may not be able to be charged  
when connected to some USB devices.  
Troubleshooting  
For details, see "About the battery" (  
page 9).  
Before requesting service  
The battery charge doesn't last long.  
,
The charge may run out sooner depending on the storage method,  
usage conditions or environment factors. For details, see "About  
Go through this section if you experience difficulty in operating the  
PSP® system. Should any problem persist, call the PSP® service line at  
the number listed on your warranty card for assistance.  
page 9).  
EN  
Screen  
Power, battery and charging issues  
The power does not turn on.  
The screen suddenly turns dark.  
,
If "Backlight Auto-Off" under  
set, the LCD screen's backlight will automatically turn off if the  
system is left inactive for the set amount of time.  
(Power Save Settings) has been  
,
The battery charge may have run out. Charge the battery.  
Check that the battery pack is properly inserted.  
,
,
If "Auto Sleep" under  
system will automatically enter sleep mode if left inactive for the  
set amount of time.  
(Power Save Settings) has been set, the  
The battery does not charge, or does not fully recharge.  
,
,
,
,
,
When using the AC adaptor, check that the AC adaptor and the AC  
power cord are properly inserted in the system and the electrical  
outlet.  
When using the USB cable, check that the USB cable is fully  
inserted into the system and the USB device and that the USB  
device is turned on.  
The screen is dark and hard to see.  
Use the display button on the system front to adjust the brightness.  
,
Black or continuously lit pixels on the screen do not  
disappear.  
,
The battery may not charge efficiently or charging may take  
longer depending on the usage conditions or environmental factors  
LCD screens are made with highly precise technology, but in some  
cases, black (dark) pixels or continuously lit pixels may appear on  
the screen. This is not a system malfunction. For details, see  
during charging. For details, see "About the battery" (  
page 9).  
Check that the system connectors (such as the USB connector) and  
the AC adaptor or USB cable connectors are clean. If not, wipe the  
connector with a soft, dry cloth.  
When using the AC adaptor, check that the correct AC adaptor for  
this product is being used.  
page 4).  
Before requesting service  
13  
 
   
,
When a video output cable is connected, the volume cannot be  
changed using the PSP® system's volume + button / volume -  
button. Adjust the volume on the connected device.  
The color of the screen does not look right.  
If "Theme" under (Theme Settings) is set to "Original", the  
,
background color will automatically change at the beginning of  
each month.  
No sound comes out from the headphones or noise is  
emitted.  
,
Video cannot be output to the TV.  
Check that the headphones are fully inserted.  
,
Check that the video output cable is fully inserted into the system  
and the TV.  
,
Video from games can be output only when the TV in use and the  
cable connecting it support progressive mode screen display. Also,  
video may not be able to be output to the TV for some functions  
other than games.  
UMD™  
The system does not recognize the UMD™.  
,
Slide the POWER/HOLD switch up and hold it for at least three  
seconds until the POWER indicator turns off. Power will be  
completely cut off. After that, turn the system back on.  
,
Some TVs may not be able to output video from the PSP® system.  
When the PSP® system is connected to a TV, the screen  
suddenly goes dark.  
,
Upon starting a UMD™, a message recommending an  
update is displayed.  
If "Screensaver" under  
(Connected Display Settings) has  
been set, the screensaver is automatically activated if no  
operations are performed for a certain period of time.  
,
Update the system software. For details on updates, refer to the  
Quick Reference booklet supplied with the system.  
Sound  
Memory Stick Duo™  
There is no sound.  
The Memory Stick Duo™ cannot be inserted.  
,
,
Check that the volume is not set to zero. Try raising the volume.  
Check that the mute setting is not on. Press the sound button on the  
system front to clear the mute setting.  
,
Set the Memory Stick Duo™ in the proper direction when  
inserting.  
,
Check that media of a type that can be used with the PSP® system  
is inserted. For details, see "Compatible media" (  
,
When headphones or a video output cable is connected, no sound  
is output from the PSP® system speakers.  
The system does not recognize the Memory Stick Duo™.  
The volume does not turn up.  
If "AVLS" under (Sound Settings) is set to "On", the  
maximum volume level is restricted.  
,
If Memory Stick Duo™ media is formatted using a PC, it may not  
be recognized by the PSP® system. If this happens, copy any data  
,
Before requesting service  
14  
 
you want to keep on the PC, and then go to  
"Format Memory Stick™" and re-format.  
Check that the Memory Stick Duo™ is properly inserted. Try  
taking out the Memory Stick Duo™ and reinserting it.  
(System Settings)  
The system does not recognize music data.  
,
Check that the music data is saved in the correct folder on the  
Memory Stick Duo™. For details, refer to the user's guide  
,
(
,
,
Music data of types that are not compatible with the system will  
not be recognized.  
To play WMA format data, you must first activate "Enable WMA  
The system can't save or load data.  
,
There may be a problem with the Memory Stick Duo™. Try using  
another Memory Stick Duo™, if available.  
Playback" under  
(System Settings).  
EN  
Video  
Photo  
Videos do not play.  
Some types of data may not be able to be played.  
Images do not display.  
,
,
Depending on the image data size, certain images are not  
viewable.  
,
If images are edited using a PC, they may not be viewable.  
The system does not recognize the image data.  
,
Check that the data is saved in the correct folder on the Memory  
Stick Duo™. For details, refer to the user's guide ( page 3).  
If the file or folder name on the Memory Stick Duo™ is changed,  
or if the file or folder is moved to another location using a PC, the  
system may not recognize it.  
,
,
Images that are not compatible with the PSP® system will not be  
recognized.  
Music does not play.  
,
The playback methods may be limited for some music data that is  
distributed through the Internet. In such cases, the data may not be  
able to be played on the PSP® system.  
Network  
A connection to the network cannot be established.  
,
,
Check that the WLAN switch on the top of the system is turned on.  
If "WLAN Power Save" under (Power Save Settings) is set to  
"On", you may not be able to transmit data correctly.  
Before requesting service  
15  
 
,
,
,
,
There may be too much distance between the system and the  
access point or, when in ad hoc mode, the system and the other  
player.  
Check that the network settings are correct. Refer to the  
instructions supplied with the network equipment and by your  
Internet service provider to make the correct network settings.  
Depending on the access point setting, you may need to enter the  
system's MAC address. You can check the MAC address under  
The system does not function properly.  
,
Static electricity and other similar occurrences may affect the  
system's operation. After unplugging the AC power cord from the  
electrical outlet and disconnecting any other cables, remove the  
battery pack and AC adaptor, wait for about 30 seconds and then  
restart the system.  
,
Slide the POWER/HOLD switch up and hold it for at least three  
seconds until the power indicator turns off. The system will be  
completely turned off. Then turn on the system again.  
(System Settings)  
"System Information".  
When communicating with another system in ad hoc mode, both  
systems must be set to the same channel. You can check the  
currently set channel under  
Mode".  
If a device that causes radio interference such as a microwave oven  
is nearby, system communications may not work properly.  
(Network Settings)  
"Ad Hoc  
The date and time are reset.  
,
If the battery is not recharged and runs out, or if the battery pack  
is replaced, the system date and time settings may be reset. Follow  
the on-screen instructions to set the time and date.  
,
The Web page won't display properly.  
Some Web pages may not display properly.  
The PSP® system is not recognized by the PC when  
connected using a USB cable.  
,
,
,
Is Memory Stick Duo™ media inserted in the PSP® system?  
Check that an operating system that supports USB mass storage  
class is installed in the personal computer in use.  
Other issues  
,
When using a USB hub or other devices, depending on the  
operating environment of the PC, the Memory Stick Duo™  
inserted in the system may not be recognized by the PC. Try  
connecting the system directly to the PC using a USB cable.  
The system or AC adaptor is warm.  
,
During use, the system or AC adaptor may become warm. This is  
not a malfunction.  
,
,
If "USB Charge" under  
(System Settings) is set to "On", the  
,
When the communication function is being used, the system may  
become warmer than during normal use. This is not a malfunction.  
device may not be recognized.  
When a USB cable is used, select  
(USB Connection)  
under (Settings) after connecting the PSP® system to the PC.  
The system is turned on, but does not operate.  
,
Check that the system is not in hold mode. If it is, slide the power/  
hold switch up to clear hold mode.  
The connected USB device is not recognized by the PSP®  
system.  
,
Check that the USB connector on the top of the system is clean.  
Try wiping it with a soft, dry cloth.  
Before requesting service  
16  
 
You forgot your password.  
If you restore default settings under  
"Restore Default Settings", the system password will be reset to  
"0000". For details, refer to the user's guide ( page 3).  
,
(System Settings)  
Note that if you restore default settings, settings you have adjusted  
for options other than the system password will also be cleared.  
Once cleared, these custom settings cannot be restored by the  
system.  
EN  
The analog stick does not function properly.  
,
At a scene where the symptoms appear, move the analog stick in a  
circular motion. This will help you determine the optimum  
operating range.  
The PSP® system cannot communicate with another PSP®  
system in ad hoc mode and communication is  
disconnected.  
,
If "UMD™ Cache" under  
you may not be able to communicate properly.  
(System Settings) is set to "On,"  
Before requesting service  
17  
 
Additional information  
Video:  
H.264/MPEG-4 AVC Main Profile  
Level 3  
Music:  
H.264/MPEG-4 AVC Main Profile  
Level 3, Linear PCM,  
WARRANTY  
UMD™  
Compatible  
codecs  
Refer to the enclosed document for region-specific warranty  
information.  
ATRAC3plus™  
Memory  
Stick™  
For details, refer to the user's guide  
(
page 3).  
Specifications  
AC adaptor: DC 5.0 V  
Design and specifications are subject to change without notice.  
Power source  
Rechargeable battery pack: Lithium-Ion  
rechargeable battery pack  
PSP® (PlayStation®Portable) system  
Maximum power  
consumption  
Approx. 6 W (when charging)  
4.3 inches (16:9) full-transparent type, TFT  
LCD screen  
drive  
Approx. 169.4 × 18.6 × 71.4 mm / 6 ¾ × ¾ ×  
2 ¾ in (width × height × depth) (excludes  
largest projection)  
Approximately 16,770,000 colors displayed  
External dimensions  
Weight  
Sound  
Stereo speakers  
Approx. 189 g (including battery pack)  
5°C - 35°C / 41°F - 95°F  
Internal disc drive  
Read-only UMD™ drive  
Operating environment  
temperature  
DC IN 5V connector  
Video out/headset connector  
Hi-Speed USB  
DC OUT connector  
Interface  
UMD™ laser  
Memory Stick Duo™ slot  
Wireless LAN (IEEE 802.11b)  
Wave length  
Power  
655 - 665 nm  
Max. 0.28 mW  
Type  
Semiconductor, continuous  
WARRANTY  
18  
 
     
This product adopts S3TC texture compression technology under  
license from S3 Graphics, Co., Ltd.  
Wireless LAN  
Standard  
IEEE 802.11b  
This product includes RSA BSAFE® Cryptographic software from  
RSA Security Inc. RSA, BSAFE are either registered trademarks or  
trademarks of RSA Security Inc. in the United States and/or other  
countries.  
Modulation format  
DS-SS (IEEE 802.11b compliant)  
RSA Security Inc. All rights reserved.  
AC adaptor  
U.S. and foreign patents licensed from Dolby Laboratories.  
EN  
Input  
AC 100-240 V, 50/60 Hz  
DC 5 V, 2000 mA  
MPEG Layer-3 audio coding technology and patents licensed from  
Fraunhofer IIS and Thomson.  
Output  
Approx. 46 × 22 × 76 mm / 1 4/5 × 4/5 × 3 in  
External dimensions  
Weight  
(width × height × depth) (excludes largest  
projection)  
This product contains  
ACCESS Co., Ltd.  
Copyright © 1996-2007 ACCESS Co., Ltd.  
is a trademark or registered trademark of ACCESS Co.,  
Internet browser software of  
Approx. 100 g  
Ltd. in Japan and other countries.  
Battery pack  
This product incorporates copyright protection technology that is  
protected by method claims of certain U.S. patents and other  
intellectual property rights owned by Macrovision Corporation and  
other rights owners. Use of this copyright protection technology must  
be authorized by Macrovision Corporation, and is intended for home  
and other limited viewing uses only unless otherwise authorized by  
Macrovision Corporation. Reverse engineering or disassembly is  
prohibited.  
Battery type  
Voltage  
Lithium-ion rechargeable battery  
DC 3.6 V  
Capacity  
1200 mAh  
This product is protected by certain intellectual property rights of  
Microsoft Corporation. Use or distribution of such technology outside  
of this product is prohibited without a license from Microsoft or an  
authorized Microsoft subsidiary.  
Software  
Software developed by the NetBSD Foundation, Inc. and its  
contributors is used for the communication functions of this product.  
For more information, see  
Specifications  
19  
 
The PSP® system's RSS Channel feature uses RSS (Really Simple  
Syndication) 2.0 technology. For details on RSS 2.0, visit  
IN NO EVENT SHALL SAM LEFFLER OR SILICON  
GRAPHICS BE LIABLE FOR ANY SPECIAL, INCIDENTAL,  
INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY  
KIND, OR ANY DAMAGES WHATSOEVER RESULTING  
FROM LOSS OF USE, DATA OR PROFITS, WHETHER OR  
NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND  
ON ANY THEORY OF LIABILITY, ARISING OUT OF OR IN  
CONNECTION WITH THE USE OR PERFORMANCE OF  
THIS SOFTWARE.  
Contains Macromedia® Flash® Player technology by Adobe  
Copyright © 1995-2007 Adobe Systems Incorporated. All rights  
reserved.  
Flash, Macromedia, and Macromedia Flash are either trademarks or  
registered trademarks of Adobe Systems Incorporated in the United  
States and/or other countries.  
Portions of the PSP® system software require the following notices:  
Trademarks  
This software is based in part on the work of the Independent  
JPEG Group.  
"
", "PlayStation" and "  
" are registered trademarks, and  
"UMD" is a trademark of Sony Computer Entertainment Inc.  
Copyright © 1988-1997 Sam Leffler  
"
" and "XMB" are trademarks of Sony Corporation and Sony  
Copyright © 1991-1997 Silicon Graphics, Inc.  
Computer Entertainment Inc.  
Permission to use, copy, modify, distribute, and sell this software  
and its documentation for any purpose is hereby granted without  
fee, provided that (i) the above copyright notices and this  
permission notice appear in all copies of the software and related  
documentation, and (ii) the names of Sam Leffler and Silicon  
Graphics may not be used in any advertising or publicity relating  
to the software without the specific, prior written permission of  
Sam Leffler and Silicon Graphics.  
"SONY" and " " are registered trademarks of Sony Corporation.  
Also, "Memory Stick Duo", "Memory Stick PRO Duo", "Memory  
Stick PRO-HG Duo", "Memory Stick Micro", "M2", "Memory Stick",  
"
", "MagicGate" and "ATRAC" are trademarks of the same  
company.  
ATOK is a registered trademark of JUSTSYSTEM CORP. in Japan  
and other countries.  
THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT  
WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR  
OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY  
WARRANTY OF MERCHANTABILITY OR FITNESS FOR  
A PARTICULAR PURPOSE.  
Windows and Windows Media are either registered trademarks or  
trademarks of Microsoft Corporation in the United States and/or other  
countries.  
Specifications  
20  
 
Mac OS is a trademark of Apple, Inc.  
All other trademarks are the properties of their respective owners.  
About national export control  
This product may fall within the scope of national export control  
legislation. You must comply fully with the requirements of such  
legislation and of all other applicable laws of any jurisdiction in  
relation to this product.  
EN  
Notice about U.S. Export Administration  
Regulations  
This product contains software that is subject to certain restrictions  
under the U.S. Export Administration Regulations, and may not be  
exported or re-exported to U.S. embargoed destinations. In addition  
this product may not be exported or re-exported to persons and entities  
prohibited by the U.S. Export Administration Regulations.  
Specifications  
21  
 
擁擠的場所。  
接近火災警報器、自動門或其他類型之自動化設備的場所。  
由於無線電波可能會干擾某些汽車的電子裝備,於車內使用無  
LAN能時務必小心使用。  
警告  
光線刺激引發的疾光敏感性癲癇)  
若您有癲癇症狀或曾有癲癇發作經驗,需在開始遊玩前先接受醫  
生的診療。某些人可能會因受到電視螢幕中反覆閃爍的光線以及  
其他的光線刺激而引發眼睛疼痛、視覺異常、偏頭痛、痙攣或意  
識障諸如昏迷)等症光敏感性癲癇假如您在遊玩  
中遭遇上述的任何類似經驗,請立刻中止繼續使用並接受醫生的  
診療。  
廢電池請回收  
(僅適用於台灣)  
遭遇下列症狀時,要立刻中止遊玩  
DNAS  
除上述症狀外,當您感到頭痛、眼花撩亂、噁心想嘔吐、疲勞或  
類似暈車症狀,以及當眼睛、耳朵、手臂、手腕、雙腳等身體的  
某些部分感到不舒服或疼痛時,請立即中止遊玩。若在中止遊玩  
後,症狀仍沒有減退,請接受醫師的診療。  
Sony Computer Entertainment Inc.DNAS (Dynamic  
Network Authentication System),可幫助保護著作權PSP®  
主機與網路連線時的加密性。DNAS能會為了認證、著作權保  
護、帳戶阻斷、系統、規則或遊戲管理以及其他目的而自動從用  
戶的硬件與軟件擷取資訊。這些被擷取的資訊並不具足以識別個  
人的性質。各種未經認可的傳遞、公開展示、以及企圖破解認證  
程序的程式與裝置的進出口以及傳遞皆可能為法律所嚴禁。  
無線電波  
無線電波可能會影響電子設備或醫療裝例如心律調整器,  
且可能會導致這些設備或裝置故障或損壞。  
若您有使用心律調整器或其他醫療裝置,請在使用無LAN功  
能之前先詢問您的主治醫生或您身上之醫療裝置的製造廠商。  
使用無LAN能時PSP® 主機與心律調整器或其他醫療  
裝置之間保持至239)的距離。  
系統軟件  
本產品中內建的系統軟件乃Sony Computer Entertainment  
Inc.制授權。詳情請閱覽以下網站:  
請勿在下列場所使用無LAN能:  
禁止使用的場所如飛機或醫院中醫院中使PSP® 主  
機時請遵守醫院的規定。此外,在飛機中使用無LAN能  
或是於飛機起降時使PSP® 之行為,可能會導致您因為違  
反航空安全規定而受到嚴厲的懲罰。  
警告  
22  
 
 
以下規定僅適用於台灣  
根據 交通部電信總局低功率電波輻射性電機管理辦法規定:  
經型式認證合格之低功率射頻電機,非經許可,公司、商號或使  
用者均不得擅自變更頻率、加大功率或變更原設計之特性及功  
能。  
低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發  
現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使  
用。  
前項合法通信,指依電信法規定作業之無線電通信。  
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射  
性電機設備之干擾。  
CT  
警告  
23  
 
目錄  
PSP® 主機基本文書  
PSP® 主機基本文書包含以下物品:  
安全與支本文書)  
本文件包含使PSP® 主機時各項安全資訊、故障檢修、規格簡  
介和其他資訊。  
快捷參考  
本文件包PSP® 主機的基本操作資訊。  
用戶指南  
(http://manuals.playstation.net/document/)  
此線上文件需透過網際網互聯網)存取,且包含了更詳細  
PSP® 主機軟件的使用相關資訊。  
本文書中介紹的系統機能可能因使用之系統軟件的版本先後,而  
與您持有PSP® 主機不同。  
目錄  
24  
 
   
使用前注意事項  
使用和保養  
請在光線良好的地方使用本機,並與螢幕保持一段安全距離。  
避免長時間使PSP® 主機了避免眼睛疲勞玩一小時請  
15鐘。  
使用前須知事項  
使用本機以前,請先詳細閱讀本說明書,並妥善保存,以備將來  
參考之用。  
若您有遭遇下列健康問題,請立即停止使用主機。如果不良症  
狀持續存在,請立即就醫。  
頭昏眼花,噁心、疲勞或類似暈船感覺  
當眼睛、耳朵、手臂、手腕等,身體一部分感覺不舒服或疼  
痛時。  
請適切調整音量。假若音量調整過高,可能會對您的聽力或喇  
叭造成損傷。  
請將主機與附屬品放在兒童拿不到的地方保管。  
兒童可能會吞Memory Stick Duo或用連接線、吊繩纏繞  
自己,而造成身體損傷或導致意外發生、機器故障。  
請勿在開車或騎腳踏車時使用。開車或騎腳踏車時觀看螢幕或  
操作主機可能會導致發生交通意外。  
周邊的兼容性  
支援本主機的周邊裝置可能與支PSP-1000列不  
同。詳細請瀏覽以下網站。  
CT  
關於安全  
本產品是在充分重視安全性能的情況下設計的。但如果使用不  
當,任何電器產品都有可能引起火災觸電或人身傷害的潛在危  
險。為確保安全操作,請遵循以下各項規則:  
遵守所有警告條文注意事項及使用說明。  
定期檢查交流電轉換器與交流電源線是否有損壞,以及電源插  
頭或電源插座有沒有灰塵堆積。  
如果裝置出現動作不正常,或者發出異常聲音或氣味時,請立  
即停止使用,並從電源插座中拔掉交流電源線插頭及所有的其  
他連接線。  
邊走邊使用主機時請務必特別小心。  
關上光碟蓋時請小心不要夾到手指。  
切勿在靠近水的場所使用主機或附屬品。  
請只使用製造厰商指定的附屬/邊機器。  
當耳機對您的皮膚造成不適時,請勿繼續使用。  
若耳機對您的皮膚造成不適時,請立即停止使用。若停止使用  
之後,狀況仍舊沒有改善,請立即就醫。  
請勿將主機或附屬品放在高溫、濕氣極重或受日光直射的地  
方。  
PSP® 出現故障情形,請聯絡保證書上記載PSP® 消費者  
服務中心,以取得必要協助。  
請勿將主機或附屬品放在窗戶密閉的車特別是夏天。  
請勿將主機或附屬品暴露在灰塵、煙霧或蒸氣中。  
請勿讓液體或小顆粒掉入主機或附屬品中。  
請勿將主機或附屬品放在傾斜、不平穩或易受振動的地方。  
請勿投擲、掉落或踩踏主機或附屬品,或使它們受到強烈的外  
力撞擊。坐在裝PSP® 主機的袋子上或將它放在裝有重物的  
背包底部之行為可能會損壞主機。  
使用前須知事項  
25  
 
     
請勿於遊玩時強制扭PSP® 主機或使主機受到強烈外力撞擊,  
否則可能會損壞主機或導致光碟蓋開啟及射出光碟。請小心持  
用類比墊。  
請勿於使用布等物品覆蓋主機時遊玩遊戲或觀賞影像。假如您  
想於遊玩遊戲或觀賞影像時暫停或暫時收起主機,請在放入盒  
子或套子前,先讓主機進入睡眠模式。又,於使用布覆蓋主機  
時,請勿使用交流電轉換器,以避免主機出現過熱現象。  
請勿將交流電源線插入變壓器或反相器。將交流電源線插入海  
外旅行者使用的變壓器或汽車專用的反相器,可能會導致交流  
電轉換器發熱,並造成灼傷或故障。  
請勿在主機或附屬品上放置重物。  
請勿觸摸、或將異物插入主機或附屬品的端子部分。  
請勿將主機放置在信用卡等帶磁帶的物體附近。  
使用主機時請勿長時間碰觸主機或交流電轉換器。主機或交流  
電轉換器的溫度可能隨使用狀況而達40°C/104°F 或更高的  
溫度。在此情況下的長時間接觸可能會導致低溫灼*。  
* 當皮膚與相對低溫(40°C 或以/104°F 或以上物體長時間接  
觸時,便會產生低溫灼傷。  
請插入接近且容易連接的電源插座。  
液晶畫面  
使Plasma(電槳)或投影電視* 連接主機時,請勿長時間  
在電視機螢幕上顯示靜止圖像,否則可能會導致螢幕受到半永  
久性的損傷。  
液晶螢幕乃是採用玻璃製成。若受到過大的外力衝擊可能會出  
現破裂。  
* LCD型螢幕除外。  
在液晶畫面的某些特定位置可能會出現黑暗點)或持續  
性的亮點。液晶畫面出現此類現象乃是正常現象,並非故障。  
液晶畫面係使用高精密度的技術製造。但每個畫面仍可能會殘  
存極少數的暗點或持續性的亮點。又,在關閉主機後,部分已  
消滅的影像仍可能於畫面上殘存數秒鐘。  
直射的日光可能會損壞主機的液晶畫面。當於戶外或窗戶附近  
使用本主機時請務必小心。  
在寒冷的環境中使用本機時,您可能會發現圖像出現陰影或畫  
面似乎顯得比平常陰暗。此非一種故障,且螢幕會於溫度上昇  
後恢復正常。  
關於交流電轉換器和交流電源線的使用  
請勿用濕手觸摸交流電源線的端子。  
請勿在雷雨天氣中,觸摸正連接至電源插座的交流電源線、交  
流電轉換器或主機本身。  
切勿使用隨或指定使用)的電池組、交流電轉換器和交  
流電源線以外的其他電源。  
請勿讓灰塵或異物堆積於主機或附屬品等周邊機器的端子四  
周。若發現有灰塵或異物堆積於主機端子的四周或是交流電源  
線上,請在連接前使用乾淨軟布擦拭。堆積於連接端子上的灰  
塵或其他異物可能會導致火災或造成觸電。  
請勿讓畫面長時間顯示靜態影像。這可能會導致模糊的影像永  
遠殘留在畫面上。  
於您準備開始清潔或打算長時間不使用主機時,請自電源插座  
中拔出交流電源線、拔掉所有其他連接線,並從主機中取出電  
池組。  
請避免踩到或掐擠交流電源線,尤其是插頭、轉接用的便利插  
座與電源線等自主機延伸出來的組件更需注意。  
在拔下交流電源線時,請捉住電源插頭筆直地將插頭從電源插  
頭拔出。絕不能拉扯連接線或強制朝特定方向拔取。  
使用前須知事項  
26  
 
當使用無防寫開關Memory Stick Duo注意切因意外  
而覆寫或刪除資料。假如您使用的是具防寫開關Memory  
Stick Duo,您可將開關調整LOCK鎖定)位置,以避免  
資料因保存、編輯或刪除而流失。  
""注意事項  
請勿碰觸位於主機光碟蓋上""。碰""能會導  
致主機故障。  
保存資料  
請勿以下述方法使Memory Stick Duo則可能會導致資料  
的遺失或毀損。  
於載入、保存資料或進行格式化時,強硬取Memory Stick  
Duo或關閉主機電源。  
於帶有靜電或有電波干擾之區域使用。  
CT  
無論理由為何,遊戲與資料一旦遺失或毀損,通常即已無法  
尋回該遊戲或資料。因此建議您應為遊戲與資料預留備份檔  
案。Sony Computer Entertainment Inc.其子公司、關係  
企業對於因遊戲或資料的遺失或毀損而造成之損害,概不承  
擔任何責任。  
插取  
Memory Stick Duo™  
為了達到最佳效果,請遵守下列指示:  
依據著作權法,在未取得著作權人同意前,除了個人娛樂用  
途外,任何錄製的資料皆不得用於其他用途。  
收藏盒和收藏套  
PSP® 主機放入兼容的盒子中保管時關閉主機電源或讓主  
機進入睡眠模式。切勿於裝入盒子時使用主機。未使用時仍啟  
動主機,或於裝入盒子或套子中使用的行為,皆可能會導致過  
熱或主機故障。  
PSP® 主機與線控裝置進HOLD固定)模式以避免錯誤  
操作。  
請勿用手或金屬物品碰觸連接端子部A。  
當於備忘區B)書寫時,請勿過度用力。  
請勿以下述方法使用或放Memory Stick Duo™:  
放置於溫度甚高之車內等高溫場所。  
受日光直射的場所。  
非常潮濕或有腐蝕危險的場所。  
使用前須知事項  
27  
 
切勿分解主機或各種周邊  
UMD™  
請按照使用說明書來操PSP® 主機與各種周邊。嚴禁擅自分解或  
改造主機,禁止分解和使用其電路結構。擅自分解主機將喪失所  
有保障權益。此外,還有發生火災、觸電或主機故障的危險。尤  
其是液晶畫面的內部,其含有高電壓零件,非常危險。而且,讀  
UMD的雷射光若直接照射到眼睛,可能會導致視力損傷。  
請勿用手觸摸光碟背面的開口部UMD的記錄面。  
請注意不要讓灰塵、沙粒等異物或其他類型的塵埃進入或弄髒  
光碟。  
UMD出現污痕時,請使用擦拭眼鏡的乾淨軟布輕柔擦拭  
UMD的外殼表面與記錄面。切勿使用溶劑或其他化學藥劑。  
切勿使用已破損裂痕或曾修理過UMD入此UMD™  
可能會導PSP® 主機毀損或故障。  
使用基地台  
外部裝置之使用與管理  
當使PSP® 主機""能選擇無LAN地台時,可能  
會顯示非公用的基地台。請僅連接到您有權使用的個人基地台,  
或是經由商用無LAN、熱點服務提供的基地台。  
請遵守下列的注意事項,以避PSP® 不當損壞或變色、退色。  
請勿使用溶劑或其他化學藥劑擦拭外側表面。  
請勿將本產品長時間放置在橡膠或塑膠材質的附近。  
請勿使用經化學處理的抹布擦拭主機。  
在國外使用  
因各國規定,部分國家可能會對特殊類型的無線電波有所限制。  
在某些情況下,使用本主機可能會被罰款或受到其他處罰。  
開始使用類比墊前  
為取得最佳效果先進入  
(設定)  
(主機設定,  
並開"統資"窗,畫圓轉動類比墊,以調整類比墊的移  
動範圍。  
結露現象  
PSP® 主機UMD從寒冷的地方直接搬放到溫暖的場所,  
機內的透鏡UMD上可能會凝結水氣。此種現象可能會導致主  
機無法正常運作。這時,請UMD取出,關閉電源,並拔掉主  
機電源插頭。在水氣尚未蒸發之前,切勿再次放UMD(水氣  
蒸發可能需要數小時如果主機仍無法恢復正常操作的話,請  
聯絡保證書上記載PSP® 消費者服務中心,以取得必要協助。  
清潔  
為了安全著想,請在開始清潔前,先自電源插座中拔出交流電源  
線、拔掉所有其他連接線,並從主機中取出電池組。  
使用前須知事項  
28  
 
清潔外殼表面與液晶螢幕  
使用軟布輕柔擦拭。  
清潔連接端子  
主機、交流電轉換器或交流電源線的連接端子若不乾淨,請勿  
繼續使用。請使用乾布或棉質紗布擦拭灰塵。若在髒污時使  
用,可能會妨礙電流的通過。  
若耳機或線控裝置的連接端子出現污痕,可能會造成噪音或聲  
音出現中斷現象。此時請以乾淨軟布擦拭,以維持清潔乾淨。  
CT  
使用前須知事項  
29  
 
請勿讓液體掉落至電池組。沾有濕氣的電池組在完全變乾前都  
不得繼續使用。  
請將電池組放在兒童拿不到的地方保管。  
若長時間不使PSP® 主機取出電池組並放置在陰涼燥  
且兒童拿不到的地方保管。  
關於電池  
電池組注意事項  
請只使用隨附的電池組或正確搭PSP® 主機機型認定可使  
用的組件。  
警告  
充電  
請勿使用已損壞或電解液外洩的電池組。  
碰觸這些有毒物質可能會導致眼睛或皮膚受到損傷或傷害。即使  
這些有毒性化學物質非為即時性的危險,仍可能因為物質的化學  
變化而於日後造成損傷。  
您可使用交流電轉換器USB另售)替電池充電。關  
於如何充電等詳細內容,請參閱隨附的使用說明書。  
假如您不慎碰觸了這些電解液外洩的電池組排出的有毒物  
質,請即刻採取以下行動。  
電池的預估充電時間  
當有毒物質進入眼睛時,勿用手揉眼睛。應立即用乾淨清  
水沖洗眼睛並接受醫生的診療。  
使用交流電轉換器充電 220分  
當有毒物質滲入皮膚或衣服時,應立即用乾淨清水沖洗遭  
滲入部位。若引起發炎或疼痛,請迅速詢問您的家庭醫  
生。  
使USB接線充電  
約5時  
以上皆為電池電力已完全耗盡時的案例。  
請細心保管電池組。  
若不留意保管,本電池組可能會引發爆炸或導致火災、化學傷  
害。  
請勿將電池組放置於接觸火、受日光直射或曝露於太陽下、接  
近熱源的高溫場所。  
請勿造成電池組短路。  
請勿分解或擅自開啟電池組。  
為避免對電池組造成損害,請勿與硬幣或鑰匙等金屬物品一同  
攜帶或保管電池組,否則可能會造成無法繼續使用的永久性損  
害。  
提示  
請勿於電池組未裝入主機時,使用已連接交流電轉換器PSP® 主  
機。若交流電轉換器突然被拔起,可能會導致主機故障。  
10° C 至 30° C/50° F 至 86° F 的溫度間為電池充電其他溫度  
間的充電動作可能無效。  
充電時若開啟主機電源或使USB接線,可能會延長充電時間。  
USB電時利用經由USB連接之裝置USB連接埠供給電源。  
要連PSP® 主機並替電池充電時,須配備高電力USB接埠。若  
使用低電力USB接埠USB hub集線器電池可能無法確實  
充電。  
同時連接交流電轉換器USB接線時池會利用交流電轉換器供  
給的電力充電。  
請勿投擲、掉落電池組,且不可使其受到強烈的外力衝擊。  
請勿在電池組上放置重物或施加重壓。  
關於電池  
30  
 
   
切勿於使用或PSP® 主機充電時拔除電池蓋。電池若忽然彈出,可  
能會導致電池掉落或毀損,並可能導致主機故障。  
更換電池組  
爲了安全起見,請在更換電池組之前先關閉主機電源並自電池  
插座拔下交流電轉換器並拔掉所有其他連接線。  
電池的預估持續時間  
若於電池電力已耗盡或取出電池組後並未再度使PSP® 主機,  
則日期與時間的設定可能會被重新設定。於發生此類情形時,  
主機會於再度啟動時,顯示日期與時間的設定畫面。  
遊戲  
約3 - 6*1  
約3 - 5*2  
播放影像  
保存電池組  
*1 選擇單人遊玩模式使用線控裝置與耳機未使用無LAN用  
附屬電池組的測試結果。  
*2 選擇交替使用主機喇叭、耳機,且切換各種音量與畫面亮度的測試  
結果。  
CT  
若長時間不使PSP® 主機,請從主機中取出電池組並放置在陰  
涼、乾燥且兒童拿不到的地方保管。  
提示  
電池使用時間會視遊戲內容與使用狀況,例如畫面亮度與環境因素,  
而有所不同。隨著電池組壽命的耗減,電池使用時間可能會逐漸縮  
短。  
電池組壽命  
電池組的壽命有限。電池續航使用時間)會因重複使用  
的次數與時間而不斷減少。若電池續航力變得極度短暫,就代  
表可能必須更換電池組。  
電池組的壽命會依其放置狀態、使用情形以及溫度等環境因素  
而有所不同。  
關於電池  
31  
 
*2 支援平行資料傳高速資料傳輸。  
*3 使Memory Stick Micro必須先將它插M2 Duo寸的轉  
接卡Memory Stick Micro直接插入主機能無法正確辨  
識。  
相容媒體  
PSP® 主機可使用下列的媒體。  
於本說明書中"Memory Stick Duo"詞乃包括了所有以下列  
Memory Stick媒體。  
提示  
標準尺寸Memory Stick無法在本主機上使用。  
不保證所Memory Stick媒體的正常動作。  
假若使用個人電腦等PSP® 以外的裝置Memory Stick Duo格式  
類型  
標誌  
化,主機可能無法正確辨識。遭遇此類情形時,請選擇  
(主機  
設定) "Memory Stick格式"Memory Stick Duo重  
新格式化。  
UMD™  
Memory Stick Duo™  
(不支MagicGate)  
UMD™  
UMD具有指定銷售區域的區域碼。本主機僅適用區域碼為  
"ALL""3"UMD。  
MagicGateMemory Stick  
Duo™  
*1  
Memory Stick Duo™  
(支MagicGate)  
*1 *2  
Memory Stick™  
*1*2  
Memory Stick PRO Duo™  
平行資料傳高速資料傳輸)  
Memory Stick PRO-HG  
Duo™  
平行資料傳輸乃是一種可同時使Memory Stick的複數資料  
/平行介面)的高速資料傳輸技術。PSP® 主機支  
4-bit行傳輸的資料。然而,載/入的必須時間可能因  
儲存時使用的媒體而異。  
*1 *2  
Memory Stick Micro™  
*1 *2 *3  
(M2™)  
*1 支MagicGate™  
相容媒體  
32  
 
   
檔案大小限制  
Memory Stick採用之檔案系統規格的限制,僅能儲存或播  
4GB下的單一檔案。  
MagicGate  
SONY司開發的著作權保護技術之名  
稱。  
CT  
相容媒體  
33  
 
, 使USB接線連接部USB置時機可能無法充電詳  
細請參"於電"30。  
故障檢修  
送修前  
電池無法持久。  
, 充電量可能因儲存方法、使用狀況或環境等因素,而出現無  
法持久的現象。詳細請參"於電"30。  
在使PSP® 主機時,如果操作上遭遇到困難,請閱讀下面的文  
章,以便找到問題的可能原因。如果仍無法解決問題,請聯絡保  
證書上記載PSP® 消費者服務中心。  
畫面  
電源、電池以及充電  
畫面突然變暗。  
, 啟用 (省電設定"動關閉背光"晶螢幕的  
背光燈將會於主機到達預定時間後自動關閉。  
, 啟用 (省電設定"動睡"機將會於到達預  
定時間後自動進入睡眠模式。  
無法接通電源。  
, 電池電力可能已經耗盡。請替電池充電。  
, 確認電池組是否已正確安裝。  
無法替電池充,無法充飽電。  
畫面晦暗且甚難辨識。  
, 使用交流電轉換器時,請確認交流電轉換器與交流電源線是  
否已正確插入主機與電源插座。  
, 請使用主機前面的顯示按鈕,調整畫面的亮度。  
, 使USB接線時USB接線是否已確實完全插入主  
USB置。同時並請確認USB置是否已打開電源。  
畫面上出現黑點或亮點且不會消失。  
, 液晶畫面係使用高精密度的技術製造,但仍可能於螢幕上殘  
存黑暗點)或持續性的亮點。此非故障,詳細請參閱  
, 電池可能會因充電時使用環境的周圍溫度而無法完全充飽電  
或需花費較長時間充電。詳細請參"於電"  
"使用前須知事"(  
25。  
畫面顏色顯示不正確。  
, 確認主機的連接端(USB接埠等交流電轉換器USB連  
接線的連接端等是否乾淨。若出現污痕,請使用乾淨軟布輕  
柔擦拭。  
,
(主題設定"""始預"景顏色  
會於每月的第一天自動改變。  
, 使用交流電轉換器時,請確認是否使用產品隨附的正規交流  
電轉換器。  
送修前  
34  
 
   
影像無法輸出至電視機。  
沒有聲音從耳機發出或雜音頻繁時。  
, 請確認影像輸出連接線是否已確實完全插入主機和電視機。  
, 請確認耳機是否已確實完全插入。  
, 從遊戲輸出的影像僅能輸出至連接線正插入支援  
Progressive(逐行掃描示模式且正使用的電視機中其  
次,影像可能因遊戲的部分機能而無法輸出至電視機。  
UMD  
, 部分電視機可能無法輸PSP® 傳輸的影像。  
主機無法辨UMD。  
, POWER電源)/HOLD固定)按鈕需至少向上滑動三秒  
鐘,直POWER電源)指示燈熄滅。此後,電源將完全關  
閉,且可收起主機。  
PSP® 主機已與電視機連接,畫面卻突然一片漆黑。  
, 設定  
(外部顯示器設定"幕保護程"幕保  
CT  
護程式會自動於一段時間都未執行任何操作後自動啟動。  
於啟UMD時,顯示要求更新的訊息。  
, 更新系統軟件新的詳細資訊參閱主機隨附"捷參  
"。  
聲音  
無聲。  
, 確認音量是否設定為零,並嘗試提高音量。  
Memory Stick Duo  
, 確認是否開啟靜音設定。請按下主機前面的聲音按鈕以解除  
靜音設定。  
無法插Memory Stick Duo。  
, 插入耳機或連接影像輸出連接線時,不會自主機的喇叭產生  
任何聲音。  
, 確認插入Memory Stick Duo的插入方向是否正確。  
, 請確認插PSP® 主機的媒體是否屬支援的類型細請參閱  
32。  
無法提高音量。  
, 將  
量。  
(聲音設定"AVLS"調"開"限制最大音  
主機無法辨Memory Stick Duo。  
, PSP®主機可能無法辨識利用電腦進行格式化的Memory Stick  
, 連接影像輸出連接線時法使PSP® 主機的音量/量  
-按鈕改變音量。請經由已連接之裝置調整音量。  
Duo遇此類情形時先將所有資料複製至備檔用的電  
選擇  
(主機設定)  
"Memory Stick格式"  
重新格式化。  
送修前  
35  
 
, 確認是否已正確插Memory Stick Duo。請嘗試取出  
主機無法辨識音樂資料。  
Memory Stick Duo並重新插入。  
, 確認音樂資料是否被正確地保存Memory Stick Duo的資  
料夾中情請參閱用戶指(  
主機無法保存或載入資料。  
, 音樂資料的檔案格式與主機不相容時,便無法正確辨識。  
, Memory Stick Duo可能已經故障。請嘗試選用另一張  
Memory Stick Duo。  
, 開始播放WMA資料前先啟用  
"。  
(主機設定"啟動WMA  
影像  
相片  
沒有播放影像。  
無法顯示圖像。  
, 部份類型的資料可能無法播放。  
, 部份圖像可能因資料容量過大而無法顯示。  
主機無法辨識影像資料。  
, 曾使PC輯加工的圖像可能無法顯示。  
, 影像資料的檔案格式與主機不相容時,便無法正確辨識。  
主機無法辨識圖像資料。  
, Memory Stick Duo的檔案或資料夾名稱遭到  
更改,或是使用電腦將檔案或資料夾移動至其他位置,則主  
機將可能無法正確辨識。  
, 確認資料是否被正確地保存Memory Stick Duo的資料夾  
中。詳情請參閱用戶指(  
, Memory Stick Duo的檔案或資料夾名稱遭到更改是  
使用電腦將檔案或資料夾移動至其他位置,則主機將可能無  
法正確辨識。  
音樂  
, 圖像PSP® 主機不相容時,便無法正確辨識。  
無法播放音樂。  
, 部分透過網際網路散佈之音樂資料的播放方式可能受限。遇  
此情形時,該資料可能無法經PSP® 主機播放。  
送修前  
36  
 
網路  
其他問題  
無法建立連線。  
主機或交流電轉換器很熱。  
, 確認主機上方的無LAN鈕是否已經開啟。  
, 使用時主機或交流電轉換器可能會變熱。並非故障。  
, 將  
(省電設定"線區域網路省電模"調"開"  
, 使用通訊機能時,主機可能會比平常使用時更熱。此非故  
障,敬請安心。  
時,您可能無法正確傳遞資料。  
, 主機與基地台使Ad Hoc式時機與其他玩家之間  
的距離太遠。  
已打開主機電源卻無法操作。  
, 確認主機是否設定HOLD固定)模式。若是的話,請向  
上滑POWER電源)/HOLD固定)按鈕以解HOLD  
(固定)模式。  
, 確認網路連線設定是否正確。詳細請參閱網路裝置附帶的使  
用說明書或透過您的網路服務商,建立正確的網路連線設  
定。  
CT  
, 您可能會因基地台的設定問題而需要輸入主機的 MAC 位址。  
無法正確操作主機。  
選擇  
, 當透Ad Hoc式與其他主機連線時部主機必須設定為  
相同的頻道。選擇 (網路設定) "Ad Hoc式",您  
可確認已預定之頻道內容。  
(主機設定)  
"系統資訊"可確認MAC位址。  
, 靜電或其他類似情況可能影響主機操作。自電源插座中拔出  
交流電源線並拔掉所有其他連接線後,取出電池組和交流電  
轉換器,約等30鐘後重新打開主機。  
, POWER電源)/HOLD固定)按鈕需至少向上滑動三秒鐘,  
直到POWER電源)指示燈熄滅。主機完全關閉後再打開主  
機。  
, 當裝置因附近發射的微波而受到電波影響時,主機的通訊機  
能可能無法正確動作。  
網頁無法正確顯示。  
日期與時間被重新設定。  
, 部分網頁可能無法正確顯示。  
, 若電池沒有充電且電力耗盡,或是更換了電池組,主機的日  
期與時間設定值便可能會被重新設定。請遵循畫面指示,設  
定時間與日期。  
使USB接線與電腦連接時,電腦無法辨PSP® 主機。  
, Memory Stick Duo是否已插PSP® 主機?  
送修前  
37  
 
, 確認可支援 USB 大容量儲存裝置的操作系統是否已安裝至您  
使用的個人電腦中。  
, 使USB線器(USB其他裝置時腦可能會因其操作  
環境而無法辨識插入主機Memory Stick Duo。請嘗試使  
USB接線直接連接電腦與主機。  
,
(主機設定"USB"設定"開"置可能無  
法正確辨識。  
, 使USB接線時PSP® 主機與個人電腦連接後擇  
(設定)的 (USB。  
PSP® 主機無法辨識連接USB置。  
, 請確認主機上方USB接埠是否乾淨。若出現污痕,請使  
用乾淨軟布輕柔擦拭。  
您忘記了密碼。  
, 選擇  
為初期預設後,主機密碼將會被重新設定"0000"。詳細請  
參閱用戶指24。但請注意,您選擇恢復預設  
(主機設定)  
"復預"一切設定皆恢復  
後,密碼等您曾經調整過的其他設定都會被強制清除。一旦  
清除,這些自訂設定即永遠無法自動恢復。  
類比墊無法正確動作。  
, 發生此類症狀時,請畫圓般轉動類比墊。這項調整可幫助您  
決定最適宜的操作範圍。  
PSP® 無法透Ad Hoc式與另一PSP® 主機通訊或通訊被  
強制切斷。  
,
(主機設定"UMDCache"設定"開"可能無  
法正確通訊。  
送修前  
38  
 
其他資訊  
:  
H.264/MPEG-4 AVC Main  
Profile Level 3  
:  
維修責任  
UMD™  
相容  
Codec  
H.264/MPEG-4 AVC Main  
Profile Level 3, Linear PCM,  
ATRAC3plus™  
請參考記載了各地區特定維修責任之相關資訊的附帶文件。  
Memory  
Stick™  
規格  
詳情請參閱用戶指(  
CT  
交流電轉換器:DC 5.0 V  
充電式電池離子充電式電池組  
本公司保留在没有事先通知情況下,變更設定或規格之權利。  
電源  
PSP® (PlayStation® Portable)主機  
最大耗電量  
約6 W充電時)  
4.3吋(16:9透明TFT動  
約可顯1,677色  
169.4  
3
×
18.6  
×
71.4 mm / 6 3/4  
最大  
×
液晶畫面  
外觀尺寸  
/
4
×
2 3/4 in寬  
×
×
凸出部分除外)  
聲音  
立體聲喇叭  
重量  
189g包含電池組)  
內藏光碟機  
UMD光碟機  
操作溫度  
5°C - 35°C/41°F - 95°F  
DC IN 5V源端子  
影像輸出/耳機連接端  
USB接埠  
UMD雷射  
波長  
介面  
DC OUT子  
Memory Stick Duo插口  
Wireless LAN無線區域網路)  
(IEEE 802.11b)  
655-665 nm  
能量  
0.28 mW  
半導體,連續性  
類型  
維修責任  
39  
 
     
LAN  
軟件  
標準  
IEEE 802.11b  
Software developed by the NetBSD Foundation, Inc. and its  
contributors is used for the communication functions of  
this product. For more information, see  
調整格式  
DS-SSIEEE 802.11b準)  
交流電轉換器  
本產品乃基S3 Graphics, Co., Ltd.授權而採S3TC質  
壓縮技術。  
輸入  
輸出  
AC 100-240 V、50/60 Hz  
DC 5 V、2000 mA  
This product includes RSA BSAFE® Cryptographic software  
from RSA Security Inc. RSA, BSAFE are either registered  
trademarks or trademarks of RSA Security Inc. in the  
United States and/or other countries.  
4
4
46  
(寬  
×
×
22  
×
×
76 mm / 1 /5  
×
/
5
×
3 in  
外觀尺寸  
重量  
RSA Security Inc. All rights reserved.  
最大凸出部分除外)  
U.S. and foreign patents licensed from Dolby Laboratories.  
100g  
MPEG Layer-3 audio coding technology and patents licensed  
from Fraunhofer IIS and Thomson.  
電池組  
此產品附ACCESSNF覽器軟體。  
電池類型  
電壓  
鋰離子充電式電池  
DC 3.6 V  
This product incorporates copyright protection technology  
that is protected by method claims of certain U.S. patents  
and other intellectual property rights owned by  
Macrovision Corporation and other rights owners. Use of  
this copyright protection technology must be authorized  
by Macrovision Corporation, and is intended for home and  
other limited viewing uses only unless otherwise  
authorized by Macrovision Corporation. Reverse  
容量  
1200 mAh  
engineering or disassembly is prohibited.  
規格  
40  
 
This product is protected by certain intellectual property  
rights of Microsoft Corporation. Use or distribution of  
such technology outside of this product is prohibited  
without a license from Microsoft or an authorized  
Microsoft subsidiary.  
THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT  
WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR OTHERWISE,  
INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF  
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE  
LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT OR  
CONSEQUENTIAL DAMAGES OF ANY KIND, OR ANY DAMAGES  
WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR  
PROFITS,WHETHER OR NOT ADVISED OF THE POSSIBILITY OF  
DAMAGE, AND ON ANY THEORY OF LIABILITY, ARISING OUT  
OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF  
THIS SOFTWARE.  
PSP® RSS道採用RSS (Really Simple Syndication) 2.0  
的技術。若您想了RSS 2.0詳細內容,請點選:  
Contains Macromedia® Flash® Player technology by Adobe  
Copyright © 1995-2007 Adobe Systems Incorporated. All  
rights reserved.  
Flash, Macromedia, and Macromedia Flash are either  
trademarks or registered trademarks of Adobe Systems  
Incorporated in the United States and/or other countries.  
CT  
商標  
下文PSP® 系統軟件的需注意事項。  
"
Entertainment Inc.註冊商標。"UMD"為該公司之商標。  
"、"PlayStation"和"  
"為Sony Computer  
This software is based in part on the work of the  
Independent JPEG Group.  
" ""XMB"Sony CorporationSony Computer  
Entertainment Inc.商標。  
Copyright© 1988-1997 Sam Leffler  
Copyright© 1991-1997 Silicon Graphics, Inc.  
"SONY"和" "為Sony Corporation註冊商標。  
另外"Memory Stick Duo""Memory Stick PRO Duo""Memory  
Stick PRO-HG Duo"、"Memory Stick Micro"、"M2"、"Memory  
Permission to use, copy, modify, distribute, and  
sell this software and its documentation for any  
purpose is hereby granted without fee, provided that  
(i) the above copyright notices and this permission  
notice appear in all copies of the software and  
related documentation, and (ii) the names of Sam  
Leffler and Silicon Graphics may not be used in any  
advertising or publicity relating to the software  
without the specific, prior written permission of  
Sam Leffler and Silicon Graphics.  
Stick"、"  
標。  
"、"MagicGate""ATRAC"同為該公司之商  
規格  
41  
 
ATOK is a registered trademark of JUSTSYSTEM CORP. in  
Japan and other countries.  
Windows and Windows Media are either registered trademarks  
or trademarks of Microsoft Corporation in the United  
States and/or other countries.  
Mac OS is a trademark of Apple, Inc.  
所有其他商標皆屬相關原著作權人所有。  
關於國家出口控制  
本產品可能因各國立法之規定而被列為限制出口商品。請嚴格遵  
守相關法條及任何與本產品之管轄權有關之法律規定。  
美國出口管理規則之注意事項  
本產品內建之軟件含有被認定為美國出口管理規Export  
Administration Regulations)之管制對象的加密技術,禁止出  
口或再出口至美國政府禁止出口的國家。同時,亦禁止將本產品  
出口或再出口至美國禁止交易的個人或團體。  
規格  
42  
 
 
© 2007 Sony Computer Entertainment Inc. All rights reserved.  
 
Printed in China  

Snapper Snow Blower LE317 User Manual
Sonic Alert Clock Radio SB300ss v3 User Manual
Sony Camcorder Accessories GP AVT1 User Manual
Sony Car Amplifier XDP 210EQ User Manual
Sony Computer Drive MPF920 Z User Manual
Sony Stereo System TA N9000ES User Manual
Sprint Nextel Cell Phone H 11 07 User Manual
StarTechcom Computer Hardware RS 485 422 User Manual
Sunbeam Slow Cooker HP3510 User Manual
SVAT Electronics Security Camera ISC203 User Manual