Sony Headphones MDR EX1000 User Manual

4-257-841-12(1)  
English  
Stereo headphones  
Specifications  
Type:  
Closed, dynamic  
Driver unit: 16 mm, dome type (CCAW)  
Power handling capacity:  
200 mW (IEC*)  
Features  
Operating Instructions  
Impedance: 32 Ω at 1 kHz  
Sensitivity: 108 dB/mW  
Frequency response:  
3 Hz – 30,000 Hz  
16 mm dynamic type driver units deliver a wide frequency range and broader dynamic  
range, and reproduce accurate sound  
Stereo  
Headphones  
Manual de instrucciones  
Driver unit’s diaphragm utilizing Liquid Crystal Polymer Film for highly accurate  
sound  
Cord:  
Plug:  
Mass:  
1.2 m (47 1/4 in) (OFC Litz cord, Y-type, detachable)  
Gold-plated L-shaped stereo mini plug  
Approx. 8 g (0.29 oz) (without cord)  
Thin and lightweight magnesium alloy housing to prevent unnecessary vibration for  
smooth bass response and clear mid-high range sound  
Acoustically adjusted by hand  
Secure fitting with flexible hanger  
Supplied accessories  
Closed type vertical in-the-ear headphones for wearing comfort  
7 sizes of hybrid silicone rubber earbuds for secure fit and long-term wearing comfort  
(SS, S, MS, M, ML, L, LL)  
1.2 m cord (RK-EX600LP, 1) / Hybrid silicone rubber earbuds (SS (2), S (2), MS (2),  
M (2), ML (2), L (2), LL (2)) / Noise isolation earbuds (S (2), M (2), L (2)) /  
Carrying case (1) / Card warranty (1) / Operating Instructions (1)  
MDR-EX1000  
3 sizes of noise isolation earbuds for effective attenuation of ambient noise (S, M, L)  
Detachable cord (1.2 m)  
* IEC = International Electrotechnical Commission  
Design and specifications are subject to change without notice.  
Genuine leather carrying case supplied  
©2010 Sony Corporation Printed in Japan  
Precautions  
How to use  
Please keep your headphones clean at all times especially inside the rubber earbud.  
(see fig. )  
Using the cord slider (see fig. )  
Move up and down to change the split position of the cord.  
If any dust or ear wax is inside the earbud, you may experience some listening  
difficulties.  
Listening with headphones at high volume may affect your hearing. For traffic safety,  
do not use while driving or cycling.  
Wearing the headphones (see fig. -)  
Handle the driver units carefully.  
Wear the earpiece marked in your right ear and the one marked in your left ear.  
Do not put weight or pressure on the headphones as it may cause the headphones to  
deform during long storage.  
There is a tactile dot on the unit marked to distinguish the left side.  
Cord  
slider  
The earbuds may deteriorate due to long-term storage or use.  
Install the earbuds firmly onto the headphones. If an earbud accidentally detaches and  
is left in your ear, it may cause injury.  
Do not pull the hanger or cord too hard.  
Store the earbuds where children cannot reach in order to prevent from accidental  
ingestion or choking.  
Tactile dot  
1.2 m cord  
Note on static electricity  
In particularly dry air conditions, mild tingling may be felt on your ears. This is a result  
of static electricity accumulated in the body, and not a malfunction of the headphones.  
The effect can be minimized by wearing clothes made from natural materials.  
(Gray)  
(Red)  
1
Hold the headphone as in the illustration, and curve the hanger into an ear  
shape.  
Wear the headphone placing the hanger behind the ear.  
Adjust the angle of the headphone to fit snugly.  
Adjust the hanger to fit behind the ear.  
You can order optional replacement earbuds and cord (RK-EX600LP) at your nearest  
Sony dealer.  
2
3
4
1
2
4
Hanger  
Tip  
As in the illustration, tuck the hanger and headphone toward the base of your ear to stabilize the  
headphone (see fig. -).  
If the cord is detached (see fig. -)  
Determine the right/left of the cord and headphones by checking the color of the cord  
jack and the  marks of the headphones, then insert each cord jack and tighten the  
screw collar.  
3
Notes  
Do not tighten the screw collar with the cord at an angle, or it may break.  
Do not twist the base of the hanger, or it may break.  
Installing the earbuds correctly (see fig. )  
If the earbuds do not fit your ears correctly, low-bass sound may not be heard. To enjoy  
better sound quality, change the earbuds to another size or type, or adjust the earbuds  
position to sit on your ears comfortably and fit your ears snugly. If the earbuds do not fit  
your ears, try another size or type. Confirm the size of the earbuds by checking the color  
inside (see fig. -for hybrid silicone rubber earbuds and -for noise isolation  
earbuds).  
When you change the earbuds, install them firmly on the headphones to prevent the  
earbud from detaching and remaining in your ear.  
About hybrid silicone rubber earbuds (see fig. -)  
Earbud sizes (inside color)  
Small  
Large  
Diameter  
Left: Gray, Right: Red  
High  
Height  
Low  
ML (Blue)  
M (Green)  
MS (Yellow)  
LL (Purple)  
S (Orange)  
SS (Red)  
L (Light blue)  
To clean the hybrid silicone rubber earbuds  
Remove the earbuds from the headphones, and wash them with a mild detergent  
solution.  
About noise isolation earbuds (see fig. -)  
Supplied noise isolation earbuds provides a snug fit for effective attenuation of ambient  
noise.  
Earbud sizes (inside color)  
Small  
Large  
Diameter  
S (Orange)  
M (Green)  
L (Light blue)  
Notes  
Prolonged use of the noise isolation earbuds may strain your ears due to their snug fit. If you have  
experience discomfort or pain in your ears, discontinue use.  
The pressure-relieving urethane cushion is extremely soft. Therefore, do not pinch or pull the  
urethane cushion. If the urethane cushion is broken or detached from the earbuds, it will not take its  
correct position and the earbuds will lose their noise isolation function.  
Sectional View  
Colored parts  
The pressure-relieving urethane cushion may deteriorate due to long-term storage or use. If the  
pressure-relieving power is lost and the urethane cushion becomes hard, the earbuds may lose their  
noise isolation function.  
Height  
Pressure-relieving  
urethane cushion  
Do not wash the noise isolation earbuds. Keep them dry, and avoid accumulation of water in the  
pressure-relieving urethane-cushions. Not doing so may cause early deterioration.  
Diameter  
To detach an earbud (see fig. -)  
Diameter  
While holding the headphone, twist the parts inside of the earbud and pull the earbud  
off.  
Tip  
If the earbud slips and cannot be detached, wrap it in a dry soft cloth.  
To attach an earbud (see fig. -)  
Push the parts inside of the earbud into the headphone until the projecting part of the  
headphone is fully covered.  
Carrying the headphones (see fig. )  
Bundle the cord first by using cord slider.  
1
2
Place the headphones in the inner case.  
Wind the cord around the side of the inner case and store the plug, and then  
put the inner case in the carrying case.  
Notes  
Do not close the case forcibly without winding up the cord. Otherwise, the cord may break.  
Caution regarding the carrying case  
– The carrying case is made of natural materials and its color may fade due to hair dressing or skin  
oil, and could also cause stains to other materials. Also, the pattern and color of the leather may  
vary.  
2
1
– Do not use alcohol, benzene, or thinner, as the carrying case may be damaged.  
– Wipe the carrying case with a dry towel if it becomes wet, otherwise it may discolor.  
– Do not leave the carrying case in a location subject to direct sunlight, such as in a car.  
 

Sennheiser Stereo Receiver EK 100 G3 User Manual
Shure Car Amplifier 27B8500 User Manual
Sigma Battery Charger KS 1018 User Manual
SMSC Switch TMC2005 JT User Manual
Sony Car Satellite TV System DL 55W815B 50W815B User Manual
Sony CD Player XR MS5 User Manual
Sony VCR SVT 168E User Manual
Sub Zero Refrigerator ID 30R User Manual
SVAT Electronics Security Camera CV1002 User Manual
Sylvania DVD Recorder SSR90V4 User Manual