TANDBERG Network Card D1392602 User Manual

TANDBERG Video Portal  
Data port Command Interface User Guide  
TANDBERG Video Portal  
Data port Command Interface User Guide  
Software version V 3  
D1392602  
TANDBERG  
D1392602  
1
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
1.  
Introduction  
The TANDBERG Video Portal Data port Command Interface User Guide contains guidelines on how to use the  
textual command interface supported by the Video Portal system, further referred to as Video Portal. The Data port  
Command Interface can be accessed through Telnet via the LAN interface or through RS-232 by connecting a serial  
cable to the serial interface connector, referred to as the Data port (ref. chapter 2). Three Telnet sessions can be  
connected to the Video Portal at the same time in addition to the RS-232 connection.  
If, after reading this manual, you require additional information concerning the use of the TANDBERG Video Portal  
Data port Command Interface, please contact your local TANDBERG dealer who will be able to supply you with  
relevant information for special applications.  
D1392602  
3
 
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
2.  
Connecting to the Data port Command Interface through the RS-232 port.  
The RS-232 port is a 9-pin, female, sub-D connector located on the front of the Video Portal. The port is configured  
as a DCE (Data Communications Equipment). The RS-232 port is default set to 115200 baud, 8 data bits, none  
parity and 1 stop bit from factory. The RS-232 port is also referred to as the Data port.  
2.1. Hardware and Cabling  
The pin outs for the RS-232 are defined in the following table (the DTE, Data Terminal Equipment, could be a PC  
or other device capable of serial communication).  
Pin no  
Signal  
CD  
RD  
TD  
DTR  
Description  
Direction  
To DTE  
To DTE  
From DTE  
From DTE  
1
2
3
4
5
6
7
8
9
Carrier detect  
Receive data  
Transmit data  
Data terminal ready  
Ground  
Data set ready  
Ready to send  
Clear to send  
Ring indicator  
DSR  
RTS  
CTS  
RI  
To DTE  
From DTE  
To DTE  
To DTE  
NOTE! A straight through cable should be used between the TANDBERG Video Portal’s RS-232 port and the DTE.  
The figure below illustrates the recommended cable-wiring scheme for connecting the Video Portal to a PC through  
RS-232.  
TANDBERG VIDEO PORTAL  
DCE, 9 pin  
PC  
DTE, 9 pin  
1 CD  
1 CD  
2 RD  
2 RD  
3 TD  
3 TD  
4 DTR  
5 GND  
6 DSR  
7 RTS  
8 CTS  
9 RI  
4 DTR  
5 GND  
6 DSR  
7 RTS  
8 CTS  
9 RI  
DTR and RTS are ignored. DSR, CD, and CTS are always asserted, while RI is not used.  
2.2. Troubleshooting  
D1392602  
4
 
   
TANDBERG Video Portal  
Data port Command Interface User Guide  
If communication cannot be established between the PC/terminal and the TANDBERG Video Portal’s Data port the  
following should be checked:  
Verify that the serial cable is a straight through 9-pin to 9-pin cable  
Confirm that the configuration of the PC/terminal’s serial RS-232 port is identical to the configuration of  
the TANDBERG Video Portal RS-232 port.  
Verify that the PC/terminal’s serial RS-232 port is working properly by connecting it back-to-back to  
another PC/terminal and send characters in both directions1.  
1 It requires a null-modem cable to perform this test  
D1392602  
5
 
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
3.  
Connecting to the Data port Command Interface using Telnet  
The TANDBERG Video Portal has one LAN port.  
The Video Portal’s Telnet server provides access to the Data port Command Interface through a 10/100 base T  
network interface supporting the TCP/IP protocol.  
When connected to the Video Portal, type tsh to start a t-shell from the command line. The Telnet client will receive  
a welcome message similar to the following:  
Welcome to <System Name>  
TANDBERG Video Portal Release V3.0  
SW Release Date: 2007-03-13  
NOTE! If the TANDBERG Video Portal has been protected with an IP password you will be prompted to enter this  
password before you can access the Data port Command Interface via Telnet.  
D1392602  
6
 
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
4.  
The TANDBERG Video Portal Commands  
4.1. Introduction  
Typing ‘?’ or ‘help’ when connected to the Data Port Command Interface will return a list of valid commands. The  
commands are used to control the functions of the Video Portal. A command may be followed by a set of  
parameters and sub-commands. This chapter gives a description of all valid commands for the Video Portal.  
4.1.1. Command format  
Typing ‘?’ or ‘help’ after a command will result in a usage text (*h of help response) being displayed. Usage text  
gives information about the command format, i.e. valid parameters, sub-commands etc. An example is shown below  
(the user input is shown in bold).  
Xconf DialPlan Entry 1 NetType ?  
*h xConfiguration Dialplan Entry [1..64] NetType: <All/H324m/H323/SIP>  
"Specifies the type of network to listen for incoming connections."  
Numbers 1-64 and All/H324m/H323/SIP are parameters of the configuration (Xconf) command. Parameters are  
arguments on which the command will operate upon. Required parameters are denoted by: < >, while optional  
parameters are denoted by: [ ]. All possible values for given parameters are separated with slashes ( / ). For some  
parameters, only their names are supplied within the brackets. In these cases specific parameter values need to be  
substituted for the parameter names. Allowed parameter values, unless obvious, are provided when the commands  
are discussed.  
Sub-commands are commands grouped together within a command. Different sub-commands within a command  
may have different parameter sets. In the example below: Address and Authentication are sub-commands to the  
command H323Gatekeeper. In the same sense Mode, ID and Password are sub commands of H323Gatekeeper  
Authentication.  
xconf H323Gatekeeper ?  
*h xConfiguration H323Gatekeeper Address: <IPAddr>  
*h xConfiguration H323Gatekeeper Authentication Mode: <Auto/Off>  
*h xConfiguration H323Gatekeeper Authentication ID: <S: 0, 50>  
*h xConfiguration H323Gatekeeper Authentication Password: <S: 0, 50>  
NOTE! The Data port Command Interface is not case sensitive.  
4.1.2. Command types  
The commands can be divided into three major classes:  
Parameter Configuration Commands, Xconf.  
Status Commands, Xstat.  
D1392602  
7
 
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
User Commands, Xcom.  
Parameter Configuration Commands are commands that set a system parameter to a specific value. E.g.: The  
command Xconf telnet mode: "on" enables telnet access on the Video Portal. If the command is syntactically  
correct the Video Portal returns OK, otherwise the Video Portal returns ERROR. An example is shown below (the  
user input is shown in bold).  
Xconf telnet mode: "on"  
OK  
When issuing a Parameter Setting Command without a parameter, the Video Portal will return the command with  
the current setting. E.g.:  
Xconf telnet mode  
*c xConfiguration Telnet Mode: On  
OK  
Status Commands are commands that list different sets of system parameters. Status commands are automatically  
called when corresponding parameters are being changed.  
User Commands are commands that allow users to configure operational parameters, like option keys, service and  
dial plan entry manipulations, disk operations and system reboot.  
4.2. The commands  
The commands are divided into five groups: System Configuration Commands, General Video Portal Commands,  
System Status Commands, Debug Commands and Special Commands.  
D1392602  
8
 
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
4.2.1. System Configuration Commands  
Command:  
alplan  
Description:  
Mapping of a call onto a service or another call.  
Dialplan Entry [1..64] Enabled: <On/Off>  
Dialplan Entry [1..64] Name: <S: 0, 30>  
Dialplan Entry [1..64] NetType: <All/H324m/H323/SIP>  
Dialplan Entry [1..64] Prefix: <S: 0, 128>  
Dialplan Entry [1..64] Suffix: <S: 0, 64>  
Dialplan Entry [1..64] ServiceId: <0..64>  
Dialplan Entry [1..64] Property [1..16] Name: <S: 0, 32>  
Dialplan Entry [1..64] Property [1..16] Value: <S: 0, 64>  
Dialplan Entry [1..64] Source [1..8] ID: < 0, 65535>  
Dialplan Entry [1..64] Source [1..8] Path: <S: 0, 128>  
sub-commands:  
Each dial plan has the following general fields, i.e. Dialplan entry details:  
Enabled – If the box is checked the service becomes available.  
Name – The name of the dial plan as represented in the Dialplan Configuration  
overview.  
Net type – Inbound call net type; either H324m, H323, SIP or All. All means that  
independent of the net type the call is accepted on a match with the  
predefined Prefix and Suffix.  
Prefix - Number to which the first part of the inbound number (bnr) is matched. The  
prefix  
is specified in the dial plan entry. The prefix is stripped from the inbound  
number.  
Suffix - Number to which the last part of the inbound number (bnr) is matched. The  
suffix  
is specified in the dial plan entry. The suffix is also stripped from the inbound  
number. The part of the number which remains after stripping both prefix and  
suffix is called remainder (See also the “useremainder” option in a DID service).  
ServiceId – Select one of the services as configured in the Services menu item.  
Each dial plan has the following service specific fields:  
Property – User configurable arguments used within a service.  
Source – User configurable figures and movies used within the service.  
Argument details for the default DID service:  
For a dial plan based on a DID service the following Arguments, i.e. properties, can be  
D1392602  
9
 
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
distinguished:  
Net type - Either H324m, H323 or SIP of the outbound call.  
AV mode – This mode determines the outbound audio and video call settings. It is either  
Audio Only, Audio + Video, Auto(matic) no fallback to audio, Auto + fallback to audio  
and Auto + always fallback to audio. In the “Audio Only” mode a voice call is being  
setup, even when all endpoints support both audio and video capabilities. In the “Audio  
+ Video” mode a call is only being setup when endpoints support both audio and video  
capabilities and a call with both these capabilities can be setup. In the “Auto” mode a  
call is being setup according to the capabilities of the endpoints. Of the latter, 3 versions  
can be distinguished: no fallback to audio, fallback to audio or always fallback to audio.  
In the “no fallback to audio” case either an “audio + video“ or an audio only call is being  
setup, depending on the capabilities choice of the initiating endpoint, i.e. when an “audio  
+ video” call is being setup, whereas the receiving endpoint only supports audio, the call  
is terminated. In the “fallback to audio” case capabilities can be changed to an audio  
only call when the receiving endpoint supports only audio, even when an “audio +  
video“ call is being setup by the initiating endpoint. The “always fallback to audio” case  
is used in case the telephony switch interferes or cannot handle capability renegotiation,  
therefore when an “audio + video” call fails automatically an audio call is being setup.  
Prefix – Specifies the first part, i.e. the part preceding the remainder, of the outbound  
number. The outbound prefix can be defined under “Arguments”.  
Suffix – Specifies the last part, i.e. the part appended to the remainder, of the Outbound  
number. The outbound suffix can be defined under “Arguments”.  
Use remainder - Specifies whether a particular part, i.e. the remainder, of the inbound  
number will be used to form a part of the outbound number. For a remainder to become  
non-zero a specified inbound “Prefix” has to match the first part and/or a specified  
inbound “Suffix” has to match the last part of an inbound number, however individually  
or combinations of both never fully match the complete inbound number. Both inbound  
Prefix and Suffix can be defined under “Dialplan entry details”. When “Use remainder”,  
is active the previously mentioned “remainder” will be appended to and precede the  
“Prefix” and the “Suffix” of the outbound number, respectively. The outbound “Prefix”  
and “Suffix“ precede and append, respectively, the “remainder” as to form the complete  
outbound number. The latter prefix and suffix can be defined under “Arguments”.  
Prefixes and suffixes are standard parameters of dial plans. Suppose, as an example, the  
prefix, inbound, prefix and postfix numbers equal 1234, 9876154, 9876 and 54  
respectively then the remainder equals 1 and the outbound number will be 12341. For  
the same settings with an inbound number 9876254 results in an outbound number  
12342. In case the prefix and/or suffix fully match the inbound number the remainder  
will be empty and the useremainder value will be ignored.  
Allow forwarding - After call setup the call is offloaded from the Video Portal system,  
i.e. not routed via the Video Portal system any longer, to free resources.  
Use sub number - The sub number is a number extension following the main number  
and is separated from the main number by a "*". In this way a number plan behind a  
main number can be reached directly.  
Example of a DID Dialplan for mobile to SIP calls:  
Note:  
For DID ServiceId = 1.  
avmode equals 1, 2, 3, 4 or 5 for Audio Only, Audio + Video and Auto (no fallback to  
audio), Auto + fallback to audio or Auto + always fallback to audio, respectively.  
useremainder equals 0 or 1, for No and Yes, respectively.  
*c xConfiguration Dialplan Entry 1 Enabled: On  
*c xConfiguration Dialplan Entry 1 Name: "H324m - SIP"  
*c xConfiguration Dialplan Entry 1 NetType: H324m  
D1392602  
10  
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
*c xConfiguration Dialplan Entry 1 Prefix: "207947133"  
*c xConfiguration Dialplan Entry 1 Suffix: ""  
*c xConfiguration Dialplan Entry 1 ServiceId: 1  
*c xConfiguration Dialplan Entry 1 Property 1 Name: "nettype"  
*c xConfiguration Dialplan Entry 1 Property 1 Value: "SIP"  
*c xConfiguration Dialplan Entry 1 Property 2 Name: "avmode"  
*c xConfiguration Dialplan Entry 1 Property 2 Value: "5"  
*c xConfiguration Dialplan Entry 1 Property 3 Name: "prefix"  
*c xConfiguration Dialplan Entry 1 Property 3 Value: "john.smith"  
*c xConfiguration Dialplan Entry 1 Property 4 Name: "suffix"  
*c xConfiguration Dialplan Entry 1 Property 4 Value: "@xyz.com"  
*c xConfiguration Dialplan Entry 1 Property 5 Name: "useremainder"  
*c xConfiguration Dialplan Entry 1 Property 5 Value: "0"  
*c xConfiguration Dialplan Entry 1 Property 6 Name: "allowredirectdid"  
*c xConfiguration Dialplan Entry 1 Property 6 Value: "0"  
*c xConfiguration Dialplan Entry 1 Property 7 Name: "usesubnumber"  
*c xConfiguration Dialplan Entry 1 Property 7 Value: "0"  
Example of an IVR Dialplan for mobile to H323 calls  
Note:  
For IVR ServiceId = 2.  
avmode equals 1, 2, 3, 4 or 5 for Audio Only, Audio + Video and Auto (no fallback to  
audio), Auto + fallback to audio or Auto + always fallback to audio, respectively.  
*c xConfiguration Dialplan Entry 2 Enabled: On  
*c xConfiguration Dialplan Entry 2 Name: "H324m - H323"  
*c xConfiguration Dialplan Entry 2 NetType: H324m  
*c xConfiguration Dialplan Entry 2 Prefix: "207947132"  
*c xConfiguration Dialplan Entry 2 Suffix: ""  
*c xConfiguration Dialplan Entry 2 ServiceId: 2  
*c xConfiguration Dialplan Entry 2 Property 1 Name: "nettype"  
*c xConfiguration Dialplan Entry 2 Property 1 Value: "H323"  
D1392602  
11  
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
*c xConfiguration Dialplan Entry 2 Property 2 Name: "avmode"  
*c xConfiguration Dialplan Entry 2 Property 2 Value: "4"  
*c xConfiguration Dialplan Entry 2 Property 3 Name: "prefix"  
*c xConfiguration Dialplan Entry 2 Property 3 Value: ""  
*c xConfiguration Dialplan Entry 2 Property 4 Name: "suffix"  
*c xConfiguration Dialplan Entry 2 Property 4 Value: ""  
*c xConfiguration Dialplan Entry 2 Property 5 Name: "allowredirectivr"  
*c xConfiguration Dialplan Entry 2 Property 5 Value: "0"  
*c xConfiguration Dialplan Entry 2 Property 6 Name: "DTMFInfoScreen"  
*c xConfiguration Dialplan Entry 2 Property 6 Value: "On"  
Example of an TMS Corporate Directory Dialplan for H323 calls:  
Note: For TMS ServiceId = 3.  
*c xConfiguration Dialplan Entry 3 Enabled: On  
*c xConfiguration Dialplan Entry 3 Name: "TMS corp. dir."  
*c xConfiguration Dialplan Entry 3 NetType: H323  
*c xConfiguration Dialplan Entry 3 Prefix: "90372001"  
*c xConfiguration Dialplan Entry 3 Suffix: ""  
*c xConfiguration Dialplan Entry 3 ServiceId: 4  
*c xConfiguration Dialplan Entry 3 Property 1 Name: "tmsaddress"  
*c xConfiguration Dialplan Entry 3 Property 1 Value: "10.47.1.10"  
*c xConfiguration Dialplan Entry 3 Property 2 Name: "allowredirectphonebook"  
*c xConfiguration Dialplan Entry 3 Property 2 Value: "0"  
*c xConfiguration Dialplan Entry 3 Property 3 Name: "DTMFInfoScreen"  
*c xConfiguration Dialplan Entry 3 Property 3 Value: "On"  
Example of a Menu Dialplan for H323 calls:  
Note: For TMS ServiceId = 4.  
*c xConfiguration Dialplan Entry 4 Enabled: On  
*c xConfiguration Dialplan Entry 4 Name: "Menu"  
*c xConfiguration Dialplan Entry 4 NetType: H323  
D1392602  
12  
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
*c xConfiguration Dialplan Entry 4 Prefix: "90370010"  
*c xConfiguration Dialplan Entry 4 Suffix: ""  
*c xConfiguration Dialplan Entry 4 ServiceId: 3  
*c xConfiguration Dialplan Entry 4 Property 1 Name: "allowredirectep"  
*c xConfiguration Dialplan Entry 4 Property 1 Value: "0"  
*c xConfiguration Dialplan Entry 4 Property 2 Name: "entry1_label"  
*c xConfiguration Dialplan Entry 4 Property 2 Value: "Secretary"  
*c xConfiguration Dialplan Entry 4 Property 3 Name: "entry1_nettype"  
*c xConfiguration Dialplan Entry 4 Property 3 Value: "H323"  
*c xConfiguration Dialplan Entry 4 Property 4 Name: "entry1_bnumber"  
*c xConfiguration Dialplan Entry 4 Property 4 Value: "554046"  
*c xConfiguration Dialplan Entry 4 Property 5 Name: "entry2_label"  
*c xConfiguration Dialplan Entry 4 Property 5 Value: "Phone Book"  
*c xConfiguration Dialplan Entry 4 Property 6 Name: "entry2_nettype"  
*c xConfiguration Dialplan Entry 4 Property 6 Value: "H323"  
*c xConfiguration Dialplan Entry 4 Property 7 Name: "entry2_bnumber"  
*c xConfiguration Dialplan Entry 4 Property 7 Value: "90372001"  
*c xConfiguration Dialplan Entry 4 Property 8 Name: "entry3_label"  
*c xConfiguration Dialplan Entry 4 Property 8 Value: "Manual Dial"  
*c xConfiguration Dialplan Entry 4 Property 9 Name: "entry3_nettype"  
*c xConfiguration Dialplan Entry 4 Property 9 Value: "H323"  
*c xConfiguration Dialplan Entry 4 Property 10 Name: "entry3_bnumber"  
*c xConfiguration Dialplan Entry 4 Property 10 Value: "90370003"  
*c xConfiguration Dialplan Entry 4 Property 11 Name: "entry4_label"  
*c xConfiguration Dialplan Entry 4 Property 11 Value: "Support"  
*c xConfiguration Dialplan Entry 4 Property 12 Name: "entry4_nettype"  
*c xConfiguration Dialplan Entry 4 Property 12 Value: "H323"  
*c xConfiguration Dialplan Entry 4 Property 13 Name: "entry4_bnumber"  
*c xConfiguration Dialplan Entry 4 Property 13 Value: "554046"  
D1392602  
13  
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
*c xConfiguration Dialplan Entry 4 Property 14 Name: "entry5_label"  
*c xConfiguration Dialplan Entry 4 Property 14 Value: "Menu"  
*c xConfiguration Dialplan Entry 4 Property 15 Name: "entry5_nettype"  
*c xConfiguration Dialplan Entry 4 Property 15 Value: "H323"  
*c xConfiguration Dialplan Entry 4 Property 16 Name: "entry5_bnumber"  
*c xConfiguration Dialplan Entry 4 Property 16 Value: "90370018"  
Ethernet  
Sets LAN port speed.  
NOTE! The Video Portal needs to reboot before the changes will apply.  
Ethernet <speed>  
---  
parameters:  
speed: auto/10half/10full/100half/100full. The speed is either set to auto or manually  
from 10mb half duplex to 100mb full duplex. When set to auto the Video Portal will  
automatically negotiate with the network and use the best available setting.  
Example of Ethernet feedback:  
*c xConfiguration Ethernet Speed: Auto  
H323CallSetup  
Configures for direct or via gatekeeper calling  
H323CallSetup Mode: <Direct/Gatekeeper>  
--  
Example of H323CallSetup feedback:  
*c xConfiguration H323CallSetup Mode: Direct  
H323Gatekeeper  
Sets gatekeeper parameters.  
NOTE! H.323 services must be set before the Video Portal can be registered to a gatekeeper.  
H323Gatekeeper Address <IPAddr>  
or  
H323Gatekeeper Authentication Mode <Auto/Off>  
or  
H323Gatekeeper Authentication ID: <S: 0, 50>  
Or  
H323Gatekeeper Authentication Password: <S: 0, 50>  
---  
sub-commands:  
Authentication Mode configures the use of authentication against a gatekeeper.  
Authentication ID Configures the user name used within an authentication challenge  
Authentication Password sets the password used within the authentication process.  
NOTE! Authentication Password is write only.  
Example of H323Gatekeeper feedback:  
D1392602  
14  
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
Xconf H323Gatekeeper Authentication  
*c xConfiguration H323Gatekeeper Authentication Address: “abc.def.ghi.jkl”  
*c xConfiguration H323Gatekeeper Authentication Mode: Off  
*c xConfiguration H323Gatekeeper Authentication ID: ""  
HTTP  
Enables or disables access to HTTP services.  
NOTE! Changes become effective after reboot.  
HTTP Mode <On/Off>  
Example of HTTP feedback:  
*c xConfiguration HTTP Mode: On  
HTTPS  
Enables or disables access to HTTPS services.  
NOTE! Changes become effective after reboot. Without https no web GUI is available.  
HTTPS Mode <On/Off>  
Example of HTTPS feedback:  
*c xConfiguration HTTPS Mode: Off  
IP  
Configures the LAN interfaces when static IP address allocation is used.  
NOTE! The Video Portal needs to reboot before the changes will take effect.  
IP Assignment: <DHCP/Static>  
or  
IP Address <IPAddr>  
or  
IP Address Subnetmask <Subnetmask>  
or  
IP Address Gateway <IPAddr>  
or  
IP Address DNS Server [1..5] Address <IPAddr>  
or  
IP Address DNS Domain Name <S: 0, 64>  
---  
parameters:  
DNS Server: Number identifying one of 5 DNS servers which can be configured. If this  
parameter is omitted the command applies to the first configuration (1).  
sub-commands:  
Assignment: Selects between DHCP (Dynamic Host Configuration Protocol) or static  
IP address allocation. When DHCP is selected the Video Portal will automatically  
receive all the necessary information from the DHCP server. This function should be  
used when the Video Portal is connected to a LAN using DHCP. When using this mode,  
IP-address and IP-subnet mask are not used because the DHCP server supplies these  
parameters.  
Address: Sets the static IP address for the given LAN interface.  
Subnetmask: Sets the subnet mask variable. Subnet mask defines the network class. If  
the setting is 255.255.255.0 the local network will support up to 256 nodes, denoting a  
class C network. If the setting is 255.255.0.0 the local network is a class B network with  
65536 addressable nodes.  
D1392602  
15  
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
Gateway: Sets the gateway IP address. If a gateway is located on the LAN and the  
Video Portal needs to reach nodes through this gateway, the gateway address can be set  
using the gateway variable (the IP address of the gateway will be set automatically if the  
Video Portal is in DHCP mode)  
Domain Name: Sets the domain name string of which the gateway is part of. Minimum  
0, maximum 64 characters.  
Example of IP Address feedback:  
*c xConfiguration IP Address: "127.0.0.1"  
Loadlimit  
Sets the processor-load percentage at which calls should be routed to another Video Portal.  
LoadLimit: <0..100>  
Example of Loadlimit feedback:  
*c xConfiguration LoadLimit: 85  
Services  
Displays all configured/uploaded .ivr-file services used in dial plans.  
Services Service [1..64] Enabled: <On/Off>  
Services Service [1..64] Name: <S: 0, 30>  
Services Service [1..64] ServiceFile: <S: 0, 128>  
Services Service [1..64] Logging: <On/Off> VP ONLY!!!!!!!!!!!!!  
sub-commands:  
Enabled: <On/Off>: Enable the service.  
Name: <S: 0, 30>: Specifies the name of the service.  
ServiceFile: <S: 0, 128> Specifies which .ivr file is used as definition of this service.  
Logging: <On/Off>: Enables the service logging functionality.  
Example of Service feedback:  
*c xConfiguration Services Service 1 Enabled: On  
*c xConfiguration Services Service 1 Name: "Direct Inwards Dialing"  
*c xConfiguration Services Service 1 ServiceFile: "/tandberg/services/did.ivr"  
*c xConfiguration Services Service 1 Logging: On  
Session  
Sets a timeout time for sessions like telnet, ssh etc.  
Session TimeOut: <0..65535>  
Example of Session feedback:  
*c xConfiguration Session TimeOut: 10000  
SIP  
Configures the SIP Proxy Mode and Address settings.  
SIP Mode: <On/Off>  
or  
SIP Interface Server Address <S: 0, 255>  
or  
SIP Interface Server Type: <Auto/NortelMicrosoft/Cisco/Alcatel/Experimental>  
D1392602  
16  
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
or  
SIP Interface Transport Default: <TCP/UDP/TLS>  
---  
sub-commands:  
Mode: Specifies whether the system uses a default SIP proxy.  
Address: Specifies the IPv4 address or FQDN of the SIP proxy.  
Type: Specifies the type of the SIP proxy.  
Transport Default: Determines which transport type will be used for SIP calls to and  
from the traversal server.  
Example of SIP feedback:  
*c xConfiguration SIP Mode: On  
*c xConfiguration SIP Interface Server Address: "127.0.0.1"  
*c xConfiguration SIP Interface Server Type: Auto  
*c xConfiguration SIP Interface Transport Default: UDP  
SNMP  
Configures the SNMP.  
Note! For more information about SNMP please read the TANDBERG SNMP application note.  
SNMP Mode < On/Off/ReadOnly/TrapsOnly >  
or  
SNMP CommunityName: <S: 0, 16>  
or  
SNMP SystemContact: <S: 0, 70>  
or  
SNMP SystemLocation: <S: 0, 70>  
or  
SNMP HostIPAddr [1..3]: <IPAddr>  
---  
parameters:  
Mode: < On/Off/ReadOnly/TrapsOnly >  
Community Name: Text string of maximum 16 characters.  
System Contact: Text string of maximum 70 characters  
System Location: Text string of maximum 70 characters  
Host IP Addr: The IP addresses of max 3 SNMP trap hosts  
sub-commands:  
Mode enables or sets the mode of SNMP support  
Community Name is used to authenticate SNMP requests. SNMP requests must have  
this ‘password’ in order to receive a response from the SNMP agent in the Video Portal.  
System Contact, Used to identify the system contact via SNMP tools such as  
HPOpenView or TANDBERG Management Suite  
System Location Used to identify system location via SNMP tools such as  
HPOpenView or TANDBERG Management Suite  
Host IP Addr identifies the IP-address of the SNMP manager. Up to three different  
SNMP Trap Hosts can be defined. Your LAN administrator should provide the correct  
values for these fields  
Example of SNMP feedback:  
*c xConfiguration SNMP Mode: On  
*c xConfiguration SNMP CommunityName: "public"  
D1392602  
17  
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
*c xConfiguration SNMP SystemContact: ""  
*c xConfiguration SNMP SystemLocation: ""  
*c xConfiguration SNMP HostIPAddr 1: "127.0.0.1"  
*c xConfiguration SNMP HostIPAddr 2: "127.0.0.1"  
*c xConfiguration SNMP HostIPAddr 3: "127.0.0.1"  
SSH  
Enables or disables SSH interface on the Video Portal  
SSH Mode: <On/Off>  
---  
Example of SSH feedback:  
*c xConfiguration SSH Mode: On  
SystemUnit  
Sets the Video Portal name and password  
SystemUnit Name: <S: 0, 50>  
or  
SystemUnit Password: <S: 0, 16>  
---  
Parameters:  
Name: Text string of maximum 50 characters  
Password: Text string of maximum 16 characters  
sub-commands  
Name, sets the name of the Video Portal  
Password, sets the password of the Video Portal  
Example of SystemUnit feedback:  
*c xConfiguration SystemUnit Name: ""  
Telnet  
Enables or disables telnet interface on the Video Portal  
Telnet Mode: <On/Off>  
---  
Example of Telnet feedback:  
*c xConfiguration Telnet Mode: On  
D1392602  
18  
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
4.2.2. General Video Portal Commands  
Command:  
Description:  
ExternalManager  
This command sets the path and address of the TMS server. A message is sent to TMS when the  
Video Portal starts up to signal TMS that the Video Portal is ready.  
ExternalManager Path: <S: 0, 255>  
or  
ExternalManager Address: <S:0, 64>  
--  
sub-commands:  
Path  
Address, the IP address of the manager  
Example of ExternalManager feedback  
*c xConfiguration ExternalManager Path:  
"tms/public/external/management/SystemManagementService.asmx"  
*c xConfiguration ExternalManager Address: ""  
NTP  
This command sets the address of the NTP server.  
NTP Address: <S: 0, 64>  
--  
sub-commands:  
Address, the IP address of the server  
Example of NTP feedback  
*c xConfiguration NTP Address: "131.188.3.220"  
Options  
View and adapt option keys  
NOTE! The Video Portal needs to reboot before the changes will take effect.  
Options [1 .. 64] Key: <S: 0, 90>  
---  
sub-commands:  
Key: Option key for e.g. BRI, PRI or SS7 trunks, VP call package.  
Example of Options feedback:  
*c xConfiguration Options 1 Key: "115201SS7-1-55C3EBB7"  
*c xConfiguration Options 2 Key: "115201P1-1-6A96DAA4"  
*c xConfiguration Options 3 Key: "115201P1-2-1811D4FA"  
*c xConfiguration Options 4 Key: "115201P1-3-79828C53"  
*c xConfiguration Options 5 Key: "115201P1-4-B5E5BD4A"  
D1392602  
19  
 
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
4.2.3. System Status Commands  
Command:  
Dialplan  
Description:  
Shows the dialplan configuration.  
Example:  
*s Dialplan 1:  
Entry:  
DialplanEntryId: 1  
Enabled: On  
Name: "H323 - SIP"  
NetType: H323  
Prefix: "9047123456"  
Suffix: ""  
ServiceId: 2  
Property:  
Name: "nettype"  
Value: "SIP"  
Property:  
Name: "avmode"  
Value: "5"  
Property:  
Name: "prefix"  
Value: ""  
Property:  
Name: "suffix"  
Value: "@10.47.8.106"  
Property:  
Name: "allowredirectivr"  
Value: "0"  
Property:  
Name: "DTMFInfoScreen"  
Value: "On"  
*s/end  
OK  
Disk  
Diaplays information regarding the internal harddrive  
Disk  
Status format:  
<Status >  
<CheckDisk>  
Parameters:  
Status is either OK or ERROR  
CheckDisk indicates whether a disk is present, mounted and can be read or written to.  
Example of Disk feedback  
*s Disk (status=OK):  
CheckDisk: "Disk present"  
CheckDisk: "Disk mounted"  
CheckDisk: "Can read and write file on disk"  
*s/end  
D1392602  
20  
 
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
Ethernet  
Displays the configuration of the Ethernet interface  
Ethernet  
Status format:  
< MacAddress>  
<Speed>  
---  
Parameters:  
MacAddress, The mac address of the Ethernet interface  
Speed, The speed of the interface, possible values are Auto/10half/10full/100half/100full.  
Example of Ethernet feedback  
*s Ethernet:  
MacAddress: "00:0E:0C:5C:B5:7D"  
Speed: 100full  
*s/end  
ExternalManager Displays the configuration of the external management system (e.g. TMS).  
ExternalManager:  
Status format:  
<Address>  
<Protocol>  
<URL>  
---  
Parameters:  
Address, The IP address of the external management system  
Protocol, the protocol used to access the management system  
URL, the URL on the management system that should be opened by the Video Portal in case  
of status updates  
Example of ExternalManager feedback:  
*s ExternalManager:  
Address: ""  
Protocol: HTTP  
URL: "tms/public/external/management/SystemManagementService.asmx"  
*s/end  
Feedback [1.. 3]  
Lists the URL and feedback expressions registered for the given Feedback ID  
Feedback  
Parameters:  
status: on/off Indicates if there is HTTP feedback registered for a given Feedback ID, ref.  
command FeedbackRegister.  
Example of feedback:  
*s Feedback 1 (status=Off): /  
*s/end  
*s Feedback 1 (status=On):  
URL: "http://10.47.14.185:8000/"  
Expression: "status/call[@status="Synced"]"  
Expression: ""  
D1392602  
21  
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
Expression: ""  
Expression: ""  
Expression: ""  
Expression: ""  
Expression: ""  
Expression: ""  
Expression: ""  
Expression: ""  
Expression: ""  
Expression: ""  
Expression: ""  
Expression: ""  
Expression: ""  
*s/end  
H323Gatekeeper Displays the status of the connection with the gatekeeper.  
H323Gatekeeper  
Status format:  
<Status>  
<Address>  
<Port>  
---  
Parameters:  
Status, indicates whether the Video Portal is registered with the gatekeeper  
Address, the IP address of the connected gatekeeper  
Port, the gatekeeper port the Video Portal is connected with  
Example of H323Gatekeeper feedback:  
*s H323Gatekeeper (status=Registered):  
Address: "10.47.9.1"  
Port: 1719  
*s/end  
IP  
Displays the IP configuration of the Video Portal  
IP  
Status format:  
<Address>  
<SubnetMask>  
<Gateway>  
<DNS:  
Server 1:  
Address>  
Server 2:  
Address>  
Server 3:  
Address>  
Server 4:  
Address>  
Server 5:  
Address>  
Domain:  
D1392602  
22  
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
Name>  
---  
Parameters:  
Address, the IP address of the Video Portal  
SubnetMask, the subnetmask used for the connected network  
Gateway, the gateway to route traffic to an IP number outside the connected network  
DNS Server [1.. 5] Address, the IP numbers of maximum 5 DNS servers  
Domain, the name of the domain the Video Portal is part of.  
Example of IP feedback:  
*s IP:  
Address: "10.31.0.5"  
SubnetMask: "255.255.248.0"  
Gateway: "10.31.0.1"  
DNS:  
Server 1:  
Address: "127.0.0.1"  
Server 2:  
Address: "127.0.0.1"  
Server 3:  
Address: "127.0.0.1"  
Server 4:  
Address: "127.0.0.1"  
Server 5:  
Address: "0.0.0.0"  
Domain:  
Name: ""  
*s/end  
NTP  
Returns the IP address of the NTP server.  
Status format:  
<Status>  
<Address>  
<Port>  
<Last Update>  
<Last Correction>  
---  
Parameters:  
Status, indicates whether the NTP server is active or not.  
Address, the IP address of the NTP server.  
Port, is default 123.  
LastUpdate, indicates the last update date and time.  
Last Correction, the time correction in seconds.  
Example of NTP feedback:  
*s NTP (status=Active):  
Address: "131.188.3.220"  
Port: 123  
LastUpdate: "2006-04-10 15:21:14"  
LastCorrection: 1  
*s/end  
Options  
Display all installed option keys.  
D1392602  
23  
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
Options  
Parameters:  
----  
Example of Options feedback:  
*s Options:  
Option 1:  
Key: "115201P1-1-43F072FC"  
Description: "1 trunk"  
*s/end  
Service  
Displays all configured/uploaded services.  
Service  
Status format:  
Service [1..64]  
Example of Service feedback:  
*s Service 1 (status=Active):  
ServiceId: 1  
Enabled: On  
Name: "Direct Inwards Dialing"  
ServiceFile: "/usr/local/ividerengine/services/did.ivr"  
Logging: Off  
InstallId: 5  
*s/end  
*s Service 2 (status=Active):  
ServiceId: 2  
Enabled: On  
Name: "IVR"  
ServiceFile: "/usr/local/ividerengine/services/ivr.ivr"  
Logging: Off  
InstallId: 7  
*s/end  
*s Service 3 (status=Active):  
ServiceId: 3  
Enabled: On  
Name: "TMS Corporate Directory"  
ServiceFile: "/usr/local/ividerengine/services/tmscorpdir.ivr"  
Logging: Off  
InstallId: 9  
*s/end  
SystemLoad  
Returns the current system load in percentage.  
SystemLoad  
Status format:  
SystemLoad <1..100>  
SystemUnit  
Displays information regarding the physical system  
SystemUnit  
D1392602  
24  
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
Status format:  
<ProductType>  
<Uptime>  
<Software  
Version>  
Name>  
ReleaseDate>  
Configuration  
Telephony:>  
VideoTelephony:>  
<Hardware :  
Version>  
SerialNumber>  
MainBoard>  
AdditionalBoard>  
Configuration:  
PRI>  
TemperatureCelcius>  
TemperatureFahrenheit>  
---  
Parameters:  
ProductType, the name of the product, e.g. Video Portal  
Uptime, the time the system is running since the last reboot in seconds  
Software  
o
o
o
o
Version, the unique name of the software  
Name,  
ReleaseDate, the time and date of the build of this software  
Configuration  
Telephony, the amount of supported voice channels  
VideoTelephony, the amount of supported video channels  
Hardware  
o
o
o
o
o
Version, software ID  
SerialNumber, software serial number  
MainBoard, the ID of the main board  
AdditionalBoard, indicates extra boards in the box  
Configuration:  
PRI, the amount of PRIs in the target system  
BRI, the amount of BRIs in the target system  
TemperatureCelcius, temperature of the main board in Celcius  
TemperatureFahrenheit, temperature of the main board in Fahrenheit  
Example of SystemUnit feedback:  
*s SystemUnit:  
ProductType: "TANDBERG Video Portal"  
Uptime: 15123  
Software:  
Version: "R3.0Beta2 (TEST SW)"  
Name: "test"  
ReleaseDate: "2007-03-21, 17:54"  
Configuration:  
Telephony: 0  
VideoTelephony: 0  
Hardware:  
Version: "EP 1.0"  
SerialNumber: "43A00001"  
MainBoard: ""  
AdditionalBoard: ""  
D1392602  
25  
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
Configuration:  
PRI:41  
TemperatureCelcius: NA  
TemperatureFahrenheit: NA  
*s/end  
4.2.4. Debug Commands  
Command:  
Syslog  
Desription:  
Enables a real-time log of Bonding, H.221 and H324m, ISDN, RTSP, IVider, and IVider Engine activity.  
Note! H323 and SIP logging is presented using the following command:  
tsh –a H323 (SIP).  
Note! Logging via the serial port is limited by the speed of the serial port, which might result in loss of  
logging data. Therefore, it is advised to use Telnet instead.  
Syslog <Level> <Mask> <Volume>  
<level> = log level, 0-99, 0 turns off log  
<mask> = bitmask (default=65535):  
Mask: With this Mask the logging of different components can be turned on. The  
mask has to be used as a bit mask.  
H324m:  
ISDN:  
RTSP:  
1
4
8
(0x0001)  
(0x0004)  
(0x0008)  
IVider:  
Engine:  
FileStreamer:  
16 (0x0010)  
64 (0x0040)  
128 (0x0080)  
ContentStreamer: 256 (0x0100)  
Transcoder:  
Mux:  
Cuil:  
512 (0x0200)  
1024 (0x0400)  
2048 (0x0800)  
<volume> = message volume mask (default=0):  
Medium:  
High:  
1 (0x01)  
2 (0x02)  
Show timestamp: 4 (0x04)  
Show IP address: 8 (0x08)  
Show Process:  
16 (0x10)  
Show Session ID: 32 (0x20)  
For instance to view the logging of the H324m, Transcoder and IVider components, the mask value equals 1  
+ 512 + 32 = 545  
4.2.5. Special (Xcommand) Commands  
Command:  
Boot  
Description:  
Reboots the system.  
D1392602  
26  
 
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
Example:  
xCommand Boot  
*r Result (status=OK): /  
*r/end  
OK  
CUIL reboot request, restarting  
CheckDisk  
This command shows the presence and the status of the internal harddisk.  
Example:  
xCommand CheckDisk  
*r Result (status=OK):  
CheckDisk: "Disk present"  
CheckDisk: "Disk mounted"  
CheckDisk: "Can read and write file on disk"  
*r/end  
OK  
ClearDialplanEntries  
ClearServiceEntries  
DefaultValuesSet  
This command deletes all dial plans.  
Example:  
xCommand ClearDialplanEntries  
*r Result (status=OK):  
*r/end  
OK  
This command deletes all uploaded Services at once.  
Example:  
xCommand ClearServiceEntries  
*r Result (status=OK):  
*r/end  
OK  
This command is used to restore factory default settings. Issuing this command with no parameters  
will restore all settings except network settings and option keys.  
DefaultValuesSet Level: <1 .. 3>  
Example (restore all default factory setting):  
xCommand DefaultValuesSet  
*r Result (status=OK): /  
*r/end  
OK  
D1392602  
27  
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
Dial  
This command establishes a dial out to an end point  
Parameters:  
CalledParty: <S:0, 60> End point to be connected with the service.  
CallingParty: <S:0, 60> Service telephone number.  
NetType: <All/H324m/H323/SIP> Nettype of the end point to be called.  
CallType: <Tlph/Vtlph> Call type is either voice (Tlph), or voice and video (Vtlph).  
OK Result parameter:  
Session ID: <S: 1.. 50>  
Example:  
xCommand Dial CalledParty:0612345678 CallingParty: 0207947123 Nettype: H324m Calltype:  
Vtlph  
*r Result (status=OK):  
Dial: "dial:904023_5"  
*r/end  
OK  
DialplanEntryDelete  
This command deletes the indicated entry of a dialplan.  
Parameter:  
DialplanEntryNumber: <1..64>  
Example:  
xCommand DialplanEntryDelete: 1  
*r Result (status=OK): /  
*r/end  
OK  
DialplanEntrySwap  
This command swaps two dial plan entries in the dial plan list.  
Parameters:  
DialplanEntryNumber: <1..64>  
DialplanEntryNumber2: <1..64>  
Example:  
xCommand DialplanEntrySwap 1 3  
*r Result (status=OK):  
*r/end  
OK  
DisconnectCall  
This command disconnects a call either via the Session ID or the Call Leg ID.  
Parameter:  
CallID: <S: 0, 50> Either the Call leg ID or the Session ID.  
D1392602  
28  
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
Example:  
xCommand DisconnectCall ABCD123456  
*r Result (status=OK):  
*r/end  
OK  
EraseDisk  
This command wipes all the data from the internal harddisk  
Example:  
xCommand EraseDisk  
*r Result (status=OK):  
*r/end  
OK  
FeedbackDeregister  
Command used to deregister XML feedback over HTTP(S).  
Parameters:  
ID: <1 .. 3> ID for the registration to deregister.  
OK Result parameters:  
ID: <1 .. 3>  
ERROR Result parameters:  
Cause: <1…> Cause code specifying why the command was not accepted by the system  
Description Textual description of the cause code.  
Example:  
xCommand feedbackderegister id:1  
*r Result (status=OK):  
ID: 2  
*r/end  
OK  
FeedbackRegister  
Command used to instruct the system to return XML feedback over HTTP(S) to specific URLs.  
What parts of the Status and Configuration XML documents to monitor are specified by XPath  
expressions. The system supports issuing feedback to 3 different URLs. The system allows a total  
of 20 XPath expressions to be registered, with a maximum of 15 for a single URL.  
Parameters:  
ID: <1 .. 3> ID for the registration. If this parameter is omitted the system uses the first  
vacant ID.  
URL(r): <S: 0, 256> The URL to post feedback to.  
Expression: 1 .. 15: <S: 0, 256> XPath expression  
OK Result parameters:  
ID: <1 .. 3>  
ERROR Result parameters:  
D1392602  
29  
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
Cause: <1…> Cause code specifying why the command was not accepted by the system  
Description Textual description of the cause code.  
Example:  
expression.1:status/call  
expression.2:status/conference  
*r Result (status=OK):  
ID: 2  
*r/end  
OK  
OptionKeyAdd  
Command used to set new option keys.  
Parameters:  
Key(r): <S: 0, 90> option key  
NOTE! Always reboot the system after adding option keys, for the option key to take effect.  
Example:  
Xcommand OptionKeyAdd 115201P1-1-6A96DAA4  
*r Result (status=OK): /  
*r/end  
OK  
OptionKeyDelete  
Command used to delete option keys.  
Parameters:  
Key(r): <S: 0, 90> option key  
Example (Delete Option Key nr. 1):  
xCommand OptionKeyDelete 1  
*r Result (status=OK): /  
*r/end  
OK  
RestoreDefaultServices Command used to restore the factory default services.  
Example:  
Xcommand RestoreDefaultServices  
*r Result (status=OK): /  
*r/end  
OK  
ServiceEntryDelete  
Command used to delete services from the Video Portal.  
Parameters:  
ServiceEntryNumber(r): <1..100>  
D1392602  
30  
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
Example (Delete Service nr. 10):  
xCommand ServiceEntryDelete 10  
*r Result (status=OK): /  
*r/end  
OK  
ServiceEntrySwap  
Command used to swap service numbers.  
Parameters:  
ServiceEntryNumber(r): <1..100>  
ServiceEntryNumber2(r): <1..100>  
Example (Swap Service nr. 10 & 11):  
xCommand ServiceEntrySwap ServiceEntryNumber: 10 ServiceEntryNumber2: 11  
*r Result (status=OK): /  
*r/end  
OK  
D1392602  
31  
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
General User Commands  
About  
Shows following system information:  
Software version: R3.0  
Portions of this software are licensed under 3rd party licenses. See the CD accompanying this  
product for details.  
Help or ?  
Licence  
Displays the help menu.  
help  
Shows 3rd party licences  
License  
Available 3rd party licenses:  
1 Miscellaneous GPL-licensed software  
2 OpenSSL  
3 openssh  
4 Less  
5 libedit  
6 lsof  
7 net-snmp  
8 popt  
9 zlib  
Relkey  
Sets the release key:  
Relkey 3761349040466652  
Shows the release key:  
Relkey  
*S relkey 3761349040466652  
Xfeedback  
The special command xfeedback lets the user register user defined XPath expressions  
(with possible exposure options) to monitor changes in the data. Whenever there is a  
change in one or more elements addressed by a registered XPath expression, the part of  
the element structure containing these changes will be returned.  
xfeedback ?  
usage: xfeedback register <XPathExpression>  
or: xfeedback deregister <index>  
or: xfeedback list  
or: xfeedback paths  
-
Paths shows all expressions which can be registered.  
List shows all registered expressions.  
(note: deregistration with index=0 will deregister all registered expressions)  
Examples:  
D1392602  
32  
 
 
TANDBERG Video Portal  
Data port Command Interface User Guide  
"xfeedback register status/call" - to monitor call changes  
"xfeedback register status/call--" - to monitor only call state changes  
"xfeedback register configuration" - to monitor all configuration changes  
Xhistory  
The special command xhistory presents the status of the last 255 calls, made to or from the  
Video Portal,via a cyclic buffer mechanism.  
NOTE! If the Video Portal is registered with a Video Portal, the call history can only be  
shown on the respective Video Portal.  
xhistory ?  
usage: xhistory call [1 .. 255]  
-
Examples:  
xhistory call 1  
*l Call 1 (type=Vtlph, protocol=H323, direction=Incoming):  
LogTag: 1  
GatewayCallLogTag: 0  
RemoteNumber: "9047123456789"  
Q931Rate: 64  
DisconnectCauseValue: 16  
Duration: 67  
*l/end  
OK  
D1392602  
33  
 

Sennheiser Microphone e838 User Manual
Shark Carpet Cleaner S3101W N User Manual
Sharp Cash Register ER A320 User Manual
Shure Mixer A33LK User Manual
Shure Musical Instrument MX400D User Manual
Solio Battery Charger Mono User Manual
Sony Blu ray Player 3 452 779 111 User Manual
Sony CD Player CDP CA8ES User Manual
Sony Printer MX B400P User Manual
Sylvania TV VCR Combo SRC2109D User Manual