Sylvania TV VCR Combo RSEC313E User Manual

OWNER’S  
MANUAL  
SYLVANIA  
13-INCH COLOR TV/VCR  
RSEC313E  
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.  
As an ENERGY STAR®  
Partner, our company has  
determined that this product meets  
the ENERGY STAR® guidelines for  
energy efficiency. ENERGY STAR®  
is a U.S. registered mark.  
If you need additional assistance for set-up or operating after  
reading owner’s manual, please call TOLL FREE : 1-800-968-3429.  
Please read before using this equipment  
 
FIGURE A  
EXAMPLE OF ANTENNA GROUNDING AS PER  
NATIONAL ELECTRICAL CODE  
ANTENNA  
LEAD I N  
WI RE  
GROUND  
CL AMP  
ANTENNA  
DISCHARGE UNIT  
(NEC SECTION 810-20)  
ELECTRI C  
SERVICE  
EQUIPMENT  
GROUNDING CONDUCTORS  
(NEC SECTION 810-21)  
GROUND CLAMPS  
NEC  
-
NATIONAL ELECTRICAL CODE  
POWER SERVICE GROUNDING  
ELECTRODE SYSTEM  
(NEC ART 250, PART H)  
S2898A  
13. Outdoor Antenna grounding-If an outside antenna or  
cable system is connected to the TV/VCR, be sure the  
antenna or cable system is grounded so as to provide  
some protection against voltage surges and built-up static  
charges. Article 810 of the National Electrical Code,  
ANSI/NFPA No. 70, provides information with respect to  
proper grounding of the mast and supporting structure,  
grounding of the lead-in wire to an antenna discharge  
unit, size of grounding conductors, location of antenna-  
discharge unit, connection to grounding electrodes, and  
requirements for the grounding electrode. (Fig. A)  
19. Damage Requiring Service-Unplug this TV/VCR from  
the wall outlet and refer servicing to qualified service per-  
sonnel under the following conditions:  
a. When the power-supply cord or plug is damaged or  
frayed.  
b. If liquid has been spilled, or objects have fallen into the  
TV/VCR.  
c. If the TV/VCR has been exposed to rain or water.  
d. If the TV/VCR does not operate normally by following  
the operating instructions. Adjust only those controls that  
are covered by the operating instructions, as improper  
adjustment of other controls may result in damage and  
will often require extensive work by a qualified technician  
to restore the TV/VCR to its normal operation.  
14. Lightning-For added protection for this TV/VCR receiv-  
er during a lightning storm, or when it is left unattended  
and unused for long periods of time, unplug it from the  
wall outlet and disconnect the antenna or cable system.  
This will prevent damage to the TV/VCR due to lightning  
and power-line surges.  
e. If the TV/VCR has been dropped or damaged in any way.  
f. When the TV/VCR exhibits a distinct change in perfor-  
mance-this indicates a need for service.  
15. Power Lines-An outside antenna system should not be  
located in the vicinity of overhead power lines or other  
electric light or power circuits, or where it can fall into  
such power lines or circuits. When installing an outside  
antenna system, extreme care should be taken to keep  
from touching such power lines or circuits as contact with  
them might be fatal.  
20. Replacement Parts-When replacement parts are required,  
be sure the service technician has used replacement parts  
specified by the manufacturer that have the same charac-  
teristics as the original part. Unauthorized substitutions  
may result in fire, electric shock, injury to persons or  
other hazards.  
16. Overloading-Do not overload wall outlets and extension  
21. Safety Check-Upon completion of any service or repairs  
to this TV/VCR, ask the service technician to perform  
routine safety checks to determine that the TV/VCR is in  
proper operating condition.  
cords as this can result in a risk of fire or electric shock.  
17. Object and Liquid Entry-Never push objects of any kind  
into this TV/VCR through openings as they may touch  
dangerous voltage points or short out parts that could  
result in a fire or electric shock. Never spill liquid of any  
kind on the TV/VCR.  
22. Heat-This TV/VCR product should be situated away from  
heat sources such as radiators, heat registers, stoves, or  
other products (including amplifiers) that produce heat.  
18. Servicing-Do not attempt to service this TV/VCR your-  
self as opening or removing covers may expose you to  
dangerous voltage or other hazards. Refer all servicing to  
qualified service personnel.  
CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY  
INSERT.  
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE  
LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.  
- 3 -  
EN  
9I03  
 
PRECAUTIONS  
IMPORTANT COPYRIGHT INFORMATION  
LOCATION  
For safe operation and satisfactory performance of  
your TV/VCR, keep the following in mind when  
selecting a place for its installation:  
Shield it from direct sunlight and keep it away  
from sources of intense heat.  
Avoid dusty or humid places.  
Avoid places with insufficient ventilation for proper  
heat dissipation. Do not block the ventilation holes  
at the top or bottom of the unit. Do not place the  
unit on a carpet because this will block the ventila-  
tion holes.  
Unauthorized recording or use of broadcast televi-  
sion programming, video tape, film or other copy-  
righted material may violate applicable copyright  
laws. We assume no responsibility for the unautho-  
rized duplication, use, or other acts which infringe  
upon the rights of copyright owners.  
FCC WARNING- This equipment may gener-  
ate or use radio frequency energy. Changes or  
modifications to this equipment may cause  
harmful interference unless the modifications  
are expressly approved in the instruction man-  
ual. The user could lose the authority to oper-  
ate this equipment if an unauthorized change  
or modification is made.  
Install unit in a horizontal position.  
Avoid locations subject to strong vibration.  
Do not place the TV/VCR near strong magnetic fields.  
Avoid moving TV/VCR to locations where temper-  
ature differences are extreme.  
This equipment has been tested and found to com-  
ply with the limits for a Class B digital device, pur-  
suant to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against  
harmful interference in a residential installation.  
This equipment generates, uses, and can radiate  
radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause  
harmful interference to radio communications.  
However, there is no guarantee that interference  
will not occur in a particular installation. If this  
equipment does cause harmful interference to  
radio or television reception, which can be deter-  
mined by turning the equipment off and on, the  
user is encouraged to try to correct the interfer-  
ence by one or more of the following measures:  
1) Reorient or relocate the receiving antenna.  
2) Increase the separation between the equipment  
and receiver.  
AVOID THE HAZARDS OF  
ELECTRICAL SHOCK AND FIRE  
Do not handle the power cord with wet hands.  
Do not pull on the power cord when disconnecting  
it from an AC wall outlet. Grasp it by the plug.  
If by accident, water is spilled on your unit, unplug  
the power cord immediately and take the unit to our  
Authorized Service Center for servicing.  
Do not put your fingers or objects into the  
TV/VCR cassette holder.  
Do not place anything directly on top of the unit.  
WARNING  
Moisture condensation may occur inside the unit  
when it is moved from a cold place to a warm place  
or after heating a cold room or under conditions of  
high humidity. If a tape is played in a TV/VCR  
which has moisture, it may damage the tape and  
TV/VCR. Therefore when the condensation occurs  
inside the unit, turn the POWER button on and allow  
at least 2 hours for the unit to dry out.  
3) Connect the equipment into an outlet on a cir-  
cuit different from that to which the receiver is  
connected.  
4) Consult the dealer or an experienced radio/TV  
technician for help.  
The serial number of this product may be found on the back of the unit. No other TV/VCR has the same serial  
number as yours. You should record the number and other vital information here and retain this book as a per-  
manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.  
Date of Purchase  
Dealer Purchase from  
Dealer Address  
Dealer Phone No.  
Model No.  
Serial No.  
- 4 -  
EN  
9I03  
 
TABLE OF CONTENTS  
C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2  
C PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . .17  
NORMAL PLAYBACK . . . . . . . . . . . . . . . . . .17  
AUTO REPEAT PLAYBACK . . . . . . . . . . . . .17  
SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18  
STILL PICTURE . . . . . . . . . . . . . . . . . . . . . . .18  
PICTURE CONTROLS . . . . . . . . . . . . . . . . . .19  
C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4  
LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
AVOID THE HAZARDS OF ELECTRICAL  
SHOCK AND FIRE . . . . . . . . . . . . . . . . . . . . . .4  
WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .6  
C SUPPLIED ACCESSORIES . . . . . . . . . . . . . . .6  
C OPERATING CONTROLS AND FUNCTIONS 7  
C RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .19  
NORMAL RECORDING . . . . . . . . . . . . . . . . .20  
SKIPPING UNWANTED SCENES DURING  
RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .20  
OTR (One Touch Recording) . . . . . . . . . . . . . .20  
TIMER RECORDING . . . . . . . . . . . . . . . . . . .21  
TIMER PROGRAM EXTENSION . . . . . . . . .22  
C PREPARATION FOR USE . . . . . . . . . . . . . . . .9  
ANTENNA/CABLE CONNECTIONS . . . . . . .9  
EXTERNAL INPUT MODE . . . . . . . . . . . . . .10  
INSTALLING THE BATTERIES . . . . . . . . . . .10  
HINTS FOR AUTOMATIC TIMER  
RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .23  
C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . .10  
SELECTING THE LANGUAGE . . . . . . . . . . .10  
CLOCK SET UP (AUTO / MANUAL) . . . . . .10  
DAYLIGHT-SAVING TIME . . . . . . . . . . . . . .12  
CHANNEL SET UP . . . . . . . . . . . . . . . . . . . .13  
DELETING (OR ADDING) CHANNEL(S) . . .13  
AUTO RETURN . . . . . . . . . . . . . . . . . . . . . . .23  
WAKE UP TIMER . . . . . . . . . . . . . . . . . . . . . .23  
SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . .24  
C COPYING A VIDEO TAPE . . . . . . . . . . . . . . .24  
C ON SCREEN DISPLAY . . . . . . . . . . . . . . . . .25  
C SPECIAL FEATURES . . . . . . . . . . . . . . . . . .25  
REAL TIME TAPE COUNTER . . . . . . . . . . . .25  
AUTO REWIND-EJECT . . . . . . . . . . . . . . . . .25  
C TV OPERATION . . . . . . . . . . . . . . . . . . . . . . .14  
WATCHING A TV PROGRAM . . . . . . . . . . . .14  
GAME MODE . . . . . . . . . . . . . . . . . . . . . . . . .14  
DEGAUSSING . . . . . . . . . . . . . . . . . . . . . . . .14  
PICTURE CONTROL . . . . . . . . . . . . . . . . . . .14  
CLOSED CAPTION SYSTEM . . . . . . . . . . . .15  
V-CHIP SET UP . . . . . . . . . . . . . . . . . . . . . . . .15  
C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .25  
C TROUBLESHOOTING GUIDE . . . . . . . . . . .26  
C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .27  
C CABLE CHANNEL DESIGNATIONS . . . . . .27  
C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover  
INDICE  
CONTROLES DE OPERACIÓN Y  
SUS FUNCIONES . . . . . . . . . . . . . . . . . . . . . . . .28  
SELECCION DE IDIOMA . . . . . . . . . . . . . . . . .30  
AJUSTE DE CANAL . . . . . . . . . . . . . . . . . . . . .31  
AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . .31  
CONEXIONES DE ANTENA/CABLE . . . . . . . .30  
MODO DE ENTRADA EXTERNA . . . . . . . . . . .30  
A NOTE ABOUT RECYCLING  
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in  
accordance with your local recycling regulations.  
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-  
tions concerning chemical wastes.  
- 5 -  
EN  
9I03  
 
FEATURES  
Infrared remote control  
Trilingual on screen menu display selectable in  
English, Spanish, or French  
Zero Return–The tape returns to counter of  
0:00:00 by rewinding or fast forwarding.  
Still–Freeze the picture at any time, for close view-  
ing of a particular scene. Only tapes recorded in  
SLP mode will show a fairly clear picture.  
Digital Auto Tracking (DTR)–Automatically  
adjusts the tracking for each tape you play.  
Rental play mode–Improves playback picture  
quality from worn tapes, such as rental tapes.  
Auto repeat–Allows you to repeat the playing of a  
tape indefinitely without pressing the PLAY button.  
Time search–Lets you set the TV/VCR to advance  
the tape by entering the desired playback time you  
want to skip.  
OTR (One Touch Recording)–Instant timed  
recording from 30 to 480 minutes is possible at the  
push of the REC/OTR button.  
1 Year, 8 events (including Daily and Weekly  
Timer Recording)–The built-in timer allows you to  
record up to 8 programs at different times on dif-  
ferent channels up to 1 year in advance. The Daily  
timer allows recordings to be made of daily broad-  
casts and the Weekly timer allows recording to be  
made once a week up to the end of the tape.  
Real time counter–This shows the elapsed record-  
ing or playback time in hours, minutes and sec-  
onds. The “–” indication will appear when the tape  
is rewound further than the tape counter position  
“0:00:00”.  
181 channel capability PLL frequency synthesiz-  
er tuner with direct station call–(A converter may  
be necessary to view scrambled cable channels.)  
Auto Clock Setting–Allows you to set the clock  
function from a PBS broadcast station.  
Closed caption system–You may view specially  
labeled (cc) TV programs, movies, news, prere-  
corded tapes, etc. with either a dialogue caption or  
text display added to the program.  
Game mode–Automatically sets external input  
mode and allows TV/VCR display to be suitable  
for use with TV games.  
Auto power on and off system–Automatically  
turns on the TV/VCR when you insert the cassette,  
turns off after auto-rewind and ejects when the  
beginning of the tape is reached.  
Auto rewind when the end of a tape is  
reached–This function doesn’t occur when using  
timer recording.  
2 Step picture search operation–You can view a  
video program at a high speed or super high speed  
in either a forward or reverse direction in LP and  
SLP mode. For SP mode only high speed.  
Three different playback tape speeds : SP/LP/SLP  
Two different recording tape speeds : SP/SLP  
Auto Head Cleaner–Automatically cleans video  
heads as you insert or remove a cassette.  
Auto return–After timer recording is finished, the  
TV/VCR can return to the beginning of the record-  
ing.  
Wake up/Sleep timer–Allows you to have the  
TV/VCR automatically turn on or off at a desired  
time.  
Timer Program Extension–Allows you to shift the  
time schedule for automatic timer recording.  
V-CHIP–Enables parents to prevent their children  
from watching inappropriate material on TV.  
SUPPLIED ACCESSORIES  
Remote Control Unit  
PART NO. (NE145UD)  
2 AA Batteries  
Rod Antenna  
PART NO. (0EMN00673 or  
0EMN01599 or 0EMN01755)  
If you need to replace these accessories, please refer to the PART NO. under the illustrations and call 1-800-  
968-3429.  
Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators  
(Splitter). Contact your local electronics store for these items.  
We do not recommend the use of universal remote controls. Not all of the functions may be controlled with  
a universal remote control. If you decide to use a universal remote control with this unit, please be aware  
that the code number given may not operate this unit. In this case, please call the manufacturer of the uni-  
versal remote control.  
- 6 -  
EN  
9I03  
 
OPERATING CONTROLS AND FUNCTIONS  
NOTE:  
We do not recommend the use of universal remote controls. Not all of the functions may be controlled with  
a universal remote control.  
If you decide to use a universal remote control with this unit, please be aware that the code number given  
may not operate this unit. In this case, please call the manufacturer of the universal remote control.  
- TV/VCR FRONT PANEL -  
VIDEO  
AUDIO  
POWER  
VOLUME  
CHANNEL  
STOP/EJECT REW  
PLAY  
F.FWD  
REC/OTR  
EARPHONE  
13  
1 2  
3
4
5
6
7 8 9  
11 12  
14  
10  
- REMOTE CONTROL -  
1 VIDEO input jack– Connect to the video output  
jack of your video camera or another VCR.  
2 AUDIO input jack– Connect to the audio output  
jack of your audio equipment, video camera or  
another VCR.  
25  
7
WAKE-UP  
/SLEEP  
POWER  
EJECT  
3
CHANNEL  
RETURN  
3 POWER button– Press to turn TV/VCR on and  
off. Press to activate timer recording.  
4 VOLUME X / Y buttons– Adjust the volume level.  
5 CHANNEL K / L buttons– Press to select the  
desired channels for viewing or recording.  
You may display the main menu on the TV screen  
by pressing repeatedly this button on the TV/VCR.  
TRACKING function– Press to minimize video  
‘noise’ (lines or dots on screen) during playback  
mode. (See page 19.)  
1
4
7
2
5
8
3
6
9
24  
15  
CHANNEL  
VOLUME  
5
4
0
+100  
MENU  
DISPLAY  
MUTE  
16  
17  
8
23  
9
PLAY  
10  
REW  
F.FWD  
6 Remote Sensor Window– Receives the infrared  
signals from the remote control.  
STOP  
7
SPEED PAUSE/STILL  
RECORD  
7 EJECT button– Press in the Stop mode to remove  
tape from TV/VCR.  
STOP button– Press to stop the tape motion.  
L button–  
22  
21  
11  
18  
T-PROG.  
CLEAR  
GAME  
TIME SEARCH  
COUNTER  
RESET  
19  
20  
Press to select setting modes from the on  
screen menu.  
Press to enter digits when setting program.  
(for example: setting clock or timer program)  
- 7 -  
EN  
9I03  
 
- REAR VIEW -  
ANT.  
26  
27  
+100 button– When selecting cable channels  
which are higher than 99, press this button first,  
then press the last two digits. (To select channel  
125, first press the “+100” button then press “2”  
and “5”).  
8 REW button– Press to rewind the tape, or to view  
the picture rapidly in reverse during playback  
mode. (Rewind Search)  
s button–  
Press to select a mode from a particular menu.  
16 MENU button– Press to display the main menu on  
the TV screen.  
17 DISPLAY button– Display the counter or the cur-  
rent channel number and current time on the TV  
screen. (See page 25.)  
(for example: LANGUAGE or USER’S SET UP)  
9 PLAY button– Press to begin playback.  
K button–  
Press to select setting modes from the on  
screen menu.  
18 SPEED button– Press to choose the desired  
recording speed:SP/SLP.  
19 T-PROG. CLEAR button– Press to cancel a setting  
of timer program. (See page 23.)  
Press to enter digits when setting program.  
(for example: setting clock or timer program)  
10 F.FWD button– Press to rapidly advance the tape,  
or to view the picture rapidly in forward during  
playback mode. (Forward Search)  
COUNTER RESET button– Press to reset counter  
to 0:00:00.  
B button–  
20 GAME button– Sets the game mode and external  
input mode at the same time. (See page 14.)  
21 TIME SEARCH button– Press to activate Time  
Search mode.  
When setting program (for example: setting  
clock or timer program), press to determine  
your selection and proceed to the next step you  
want to input.  
Press to determine setting modes from on  
screen menu.  
Press to select a mode from a particular menu.  
22 PAUSE/STILL button– Press to temporarily stop  
the tape during the recording or to view a still pic-  
ture during playback.  
23 MUTE button– Mutes the sound. Press it again to  
resume sound.  
24 CHANNEL RETURN button– Press to go back to  
the previously viewed channel. For example,  
pressing this button once will change channel dis-  
play from 3 (present channel) to 10 (previously  
viewed channel), and pressing it a second time  
will return from 10 to 3.  
(for example: LANGUAGE or USER’S SET UP)  
11 RECORD(REC) button– Press for manual recording.  
OTR button– Activates One Touch Recording.  
(only on the TV/VCR)  
12 RECORD indicator– Flashes during recording.  
Lights up in the Stand-by mode for Timer  
Recording.  
13 EARPHONE jack– Connects to earphones (not  
supplied) for personal listening. The size of jack is  
1/8” monaural (3.5mm).  
25 WAKE-UP/SLEEP button– Sets the Wake up or  
Sleep Timer. (See page 23.)  
26 Power cord– Connect to a standard AC outlet  
(120V/60Hz).  
27 ANT. terminal– Connect to an antenna or cable  
system.  
14 Cassette compartment  
15 Number buttons– Press to select desired channels  
for viewing or recording. To select channels from  
1 to 9, first press the 0 button and then 1 to 9.  
- 8 -  
EN  
9I03  
 
PREPARATION FOR USE  
ANTENNA/CABLE CONNECTIONS  
From Cable System or  
Satellite Dish  
Rod Antenna  
(Supplied)  
VHF/UHF Antenna  
(Not supplied)  
Satellite Box or  
Cable Box  
OUT  
IN  
(Not supplied)  
VHF Antenna  
(Not supplied)  
UHF Antenna  
(Not supplied)  
From  
Cable System  
or  
or  
ANT  
.
VHF/UHF Combiner  
(Not supplied)  
ANT.  
or  
75-ohm Coaxial  
Cable (Not supplied)  
Flat twin-lead cable  
or  
VHF/UHF COMBINED ANTENNA  
VHF/UHF SEPARATE ANTENNAS  
The VHF/UHF Rod Antenna (supplied) is detach-  
able. Insert the stem of the antenna into the hole on  
the upper-back portion of the TV/VCR. Connect the  
VHF/UHF Rod Antenna or VHF/UHF Combination  
Antenna to the ANT. terminal of the TV/VCR as  
shown in the diagram above.  
For the best reception, fully extend the VHF/UHF  
Rod Antenna and make the necessary adjustments.  
(Avoid touching the top section when adjusting.)  
NOTE:  
In some areas it will be necessary to use an outdoor  
antenna.  
CABLE WITHOUT CONVERTER/  
DESCRAMBLER BOX  
Use this connection if your cable system connects  
directly to your TV/VCR without a converter box.  
By using this connection you can:  
1) Use the TV/VCR remote to select channels.  
2) Program one or more unscrambled channels for  
Automatic Timer Recording.  
NOTE: This unit will ONLY record and view the  
same channel.  
Before plugging the Rod antenna into antenna termi-  
nal, check that the pin is not bent. If it is bent,  
straighten the pin as illustrated, then plug the pin into  
antenna terminal.  
CABLE WITH CONVERTER/  
DESCRAMBLER BOX OR SATELLITE  
BOX  
Bent pin  
If your cable service supplies you with a converter  
box or if you use a satellite system, you can use the  
basic connection shown here.  
Cable Plug  
(Straight pin)  
(Needs to be straightened)  
By using this connection you can also record scram-  
bled channels. However, channel selection must be  
made with the converter box or satellite box. This  
means that channels cannot be changed using the  
TV/VCR Remote Control. Unattended timer record-  
ing is limited to one channel at a time.  
NOTE:  
The connection of an indoor antenna may not always  
give acceptable TV reception.  
Note to CATV system installer:  
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that  
provides guidelines for proper grounding and in particular, specifies that the cable ground shall be connect-  
ed to the grounding system of the building as close to the point of cable entry as practical.  
- 9 -  
EN  
9I03  
 
TO RECORD A SCRAMBLED/UNSCRAMBLED  
CHANNEL  
INSTALLING THE BATTERIES  
1. Set the TV/VCR channel selector to the output  
channel of the Cable Converter Box or Satellite  
Box. (Ex. CH3)  
2. Select the channel to record from your Cable  
Converter Box or Satellite Box.  
1) Open the battery compartment cover by pressing  
the cover on the remote unit in the direction of the  
arrow.  
2) Insert 2 “AA” penlight batteries into the battery  
compartment in the direction indicated by the  
polarity (+/-) markings.  
3) Replace the cover.  
EXTERNAL INPUT MODE  
When using an external input signal (another VCR or  
camcorder), connect the player’s audio/video output  
cables to the AUDIO IN/ VIDEO IN jacks of your  
TV/VCR. Then press the CHANNEL K or L button  
until “AUX” appears on the screen.  
AUX  
NOTE: “AUX” is found below the  
lowest memorized channel.  
(Example: CH2)  
SET UP FOR USE  
4 Exit the Language mode  
SELECTING THE LANGUAGE  
Press the MENU button on the remote control to  
return to TV mode.  
1 Plug in the TV/VCR power cord  
Plug the TV/VCR power cord into a  
standard AC outlet.  
NOTE: If for some reason the menu is in Spanish or  
French, press the MENU button on the remote con-  
trol, press the PLAY/K button to point to “IDIOMA  
[ESPAÑOL]” or “LANGAGE [FRANÇAIS]”, then  
press the F.FWD/B button, then press the MENU  
button on the remote control.  
NOTE:  
If some digits appear in the corner of  
the screen, press the POWER button  
without unplugging the power cord.  
Make sure ...  
Press the POWER button to turn on the TV/VCR.  
NOTE: This function effects only the language on  
the screen menu and not the audio source.  
– M E N U –  
2 Select “LANGUAGE”  
CLOCK SET UP  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
Press the MENU button on the  
(AUTO / MANUAL)  
remote control.  
Press the PLAY/K or STOP/L but-  
ton to point to “LANGUAGE”.  
B
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
The TV/VCR clock must be set correctly before VCR  
timer recording is possible. It is suggested that the  
clock be set manually when first setting up the  
TV/VCR, then set to [ON] the auto clock setting  
which will periodically correct the setting if necessary.  
NOTE: If you cannot receive a station with time  
signals, auto clock setting cannot be performed. Use  
manual setting only.  
TIME SEARCH  
3 Select “ENGLISH”, “ESPAÑOLor  
“FRANÇAIS”  
Select “ENGLISH”, “ESPAÑOL”= Spanish or  
“FRANÇAIS”= French using the F.FWD/B or  
REW/s button.  
- 10 -  
EN  
9I03  
 
MANUAL CLOCK SETTING  
8 Start the clock  
Make sure ...  
Press the MENU button on the  
remote control.  
The TV/VCR is turned on.  
In the example below, the clock is to be set to:  
5:40 PM  
Although seconds are not displayed,  
they begin counting from 00 when  
you press the MENU button on the  
remote control. Use this feature to  
synchronize the clock with the correct time.  
NOTE:  
When unplugging the AC cord or if there is a power  
failure for more than 3 seconds, you may have to  
reset the clock.  
DATE  
May 6th, 2004  
SETTING TIME 5:40PM  
1 Select “SETTING CLOCK”  
Press the MENU button on the  
remote control.  
Press the PLAY/K or STOP/L  
button to point to “SETTING  
CLOCK”.  
– M E N U –  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
B
ZERO RETURN  
TIME SEARCH  
TO CHANGE CLOCK SETTING  
Then press the F.FWD/B button.  
If you want to change the clock,  
1) Follow steps [1] and [2].  
2) Select where you want to change using the  
F.FWD/B or REW/s button.  
3) Enter correct numbers using the PLAY/K or  
STOP/L button.  
2 Select “MANUAL CLOCK SET”  
Press the PLAY/K or STOP/L  
button to point to “MANUAL  
CLOCK SET”.  
– SETTING CLOCK –  
AUTO CLOCK  
[ON]  
AUTO CLOCK CH SEARCH  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ 02 ]  
B
[OFF]  
Then press the F.FWD/B button.  
4) Press the MENU button on the remote control to  
start the clock.  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
3 Select the month  
Press the PLAY/K or STOP/L but-  
ton until your desired month  
appears. (Example: May 05)  
Then press the F.FWD/B button.  
PLEASE NOTE:  
0 5  
/
– – – – – – – – –  
If there is no local PBS station in your area or on  
your cable system, select “AUTO CLOCK” and  
press the F.FWD/B or REW/s button to turn [OFF]  
this function. Then you can manually adjust the  
clock.  
HOUR  
– –  
MINUTE  
– – – –  
:
4 Select the day  
Press the PLAY/K or STOP/L but-  
ton until your desired day appears.  
(Example: 6th 06)  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
AUTOMATIC CLOCK SETTING  
Make sure ...  
0 5  
/
0 6 – – – – – – –  
HOUR  
– –  
MINUTE  
– – – –  
The TV/VCR is turned on.  
Confirm the TV/VCR is receiving a RF (Radio  
Frequency) signal from either an antenna or cable  
system connection using the ANT. terminal on the  
rear of the TV/VCR.  
:
Then press the F.FWD/B button.  
5 Select the year  
Press the PLAY/K or STOP/L but-  
ton until your desired year appears.  
(Example: 2004)  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
0 5  
/
0 6 THU 2 0 0 4  
NOTE:  
HOUR  
– –  
MINUTE  
– – – –  
If a cable converter box is being used, make sure it  
is powered on.  
:
Then press the F.FWD/B button.  
You must use the TV/VCR remote control to per-  
form the clock setting procedure.  
6 Select the hour  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
If the TV/VCR is connected directly to a cable  
Press the PLAY/K or STOP/L but-  
ton until your desired hour appears.  
(Example: 5, PM)  
converter box or satellite box, the local PBS station  
must be selected on the cable box itself and the  
TV/VCR must be set to the output channel of the  
cable converter box or satellite box (usually chan-  
nel 3 or 4), to be able to set up or correct the clock  
automatically.  
0 5  
/
0 6 THU 2 0 0 4  
HOUR  
0 5  
MINUTE  
– – PM  
:
Then press the F.FWD/B button.  
– MANUAL CLOCK SET –  
MONTH DAY YEAR  
7 Select the minute  
Press the PLAY/K or STOP/L but-  
ton until the desired minute  
appears. (Example: 40)  
0 5  
/
0 6 THU 2 0 0 4  
HOUR  
0 5  
MINUTE  
4 0 PM  
:
- 11 -  
EN  
9I03  
 
1 Select “SETTING CLOCK”  
Press the MENU button on the  
remote control.  
Press the PLAY/K or STOP/L but-  
ton to select “SETTING CLOCK”.  
Press the F.FWD/B button to enter  
“SETTING CLOCK” menu.  
5 Turn off the TV/VCR  
Once the TV/VCR is turned off , it will periodically  
check and set the correct date and time.  
– M E N U –  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
B
ZERO RETURN  
TIME SEARCH  
DAYLIGHT-SAVING TIME  
Select this feature and the TV/VCR’s clock automati-  
cally will advance one hour in April, then reverse one  
hour in October.  
When Daylight-Saving Time is ON, the clock will  
change automatically as follows:  
– SETTING CLOCK –  
2 Set “AUTO CLOCK” to [ON]  
Press the F.FWD/B button until  
“AUTO CLOCK [ON]” appears.  
B
AUTO CLOCK  
AUTO CLOCK CH SEARCH  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ON]  
[ 02 ]  
[OFF]  
First Sunday of April : At 2 AM the clock imme-  
diately changes to 3 AM. Any timer programming  
you have set to occur between 2 AM and 3 AM  
will not record.  
3 Begin “AUTO CLOCK CH SEARCH”  
Last Sunday of October : At 2 AM the clock  
immediately changes to 1 AM.  
Make sure ...  
Press the POWER button to turn on the TV/VCR.  
Press the STOP/L button to select  
– SETTING CLOCK –  
“AUTO CLOCK CH SEARCH”.  
AUTO CLOCK  
AUTO CLOCK CH SEARCH  
[ON]  
B
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ 02 ]  
Press the F.FWD/B button.  
[OFF]  
The TV/VCR is now searching  
for the station which contain the  
auto clock set signal. The search  
for a signal may take up to 20  
seconds per channel.  
1 Select “SETTING CLOCK”  
Press the MENU button on the  
– M E N U –  
remote control.  
TIMER PROGRAMMING  
PICTURE CONTROL  
B
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
“_ _” appears at the lower left of  
the screen when the search has  
ended.  
– AUTO CLOCK CH SEARCH –  
Press the PLAY/K or STOP/L but-  
ton to point to “SETTING  
CLOCK”.  
08  
10  
13  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
Auto Clock station- write down  
Then press the F.FWD/B button.  
_ _  
the number(s) that appear on the  
screen. These are the auto clock  
station(s) in your area. See item  
4 below.  
If no number(s) appear on the TV screen, there are  
no stations in your area which contain the Auto  
Clock signal. Auto Clock Setting is not possible.  
Please use Manual Clock Setting on page 11.  
2 Set “D.S.T.(Daylight-Saving Time) to [ON]  
Press the PLAY/K or STOP/L but-  
ton to point to “D.S.T.”.  
Then press the F.FWD/B or  
– SETTING CLOCK –  
AUTO CLOCK  
[ON]  
AUTO CLOCK CH SEARCH  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ 02 ]  
B
[ON]  
REW/s button until [ON] appears.  
Press the MENU button to exit the screen.  
NOTE: During Auto Clock CH Search, the picture  
may be distorted, this is normal.  
3 Exit the Daylight-Saving Time mode  
Press the MENU button on the remote control to  
return to TV mode.  
4 Enter the channel number that contains the  
Automatic Clock Setting Signal  
Press the MENU button on the remote control.  
Press the PLAY/K or STOP/L but-  
TO CANCEL THE DAYLIGHT-SAVING  
TIME  
Repeat steps [1] to [2], select [OFF] using the  
– M E N U –  
ton to select “SETTING CLOCK”.  
Press the F.FWD/B button to  
F.FWD/B or REW/s button.  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
B
enter “SETTING CLOCK” menu.  
Press the STOP/L button to select  
“AUTO CLOCK CH”.  
Press the F.FWD/B or REW/s  
buttons until you locate Auto  
Clock Set station number. See  
item 3 above.  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
– SETTING CLOCK –  
AUTO CLOCK  
AUTO CLOCK CH SEARCH  
AUTO CLOCK CH  
MANUAL CLOCK SET  
D.S.T.  
[ON]  
B
[
45]  
[OFF]  
Press the MENU button to exit the  
screen.  
- 12 -  
EN  
9I03  
 
DELETING (OR ADDING)  
CHANNEL(S)  
The channels you no longer receive or seldom watch  
can be deleted from the memory. (Of course, you  
can add the deleted channel into the memory again.)  
CHANNEL SET UP  
You can program the tuner to scan all the channels  
you receive in your area.  
NOTE: Channel setup is NOT needed when connect-  
ed to a cable box or satellite box. Just select the  
TV/VCR channel selector to the output channel of  
the cable box or satellite box (Ex CH3), then select  
the channel to be viewed on the Cable Box or  
Satellite Box.  
1 Select “CHANNEL SET UP”  
Press the MENU button on the  
remote control.  
Press the PLAY/K or STOP/L but-  
ton to point to “CHANNEL SET  
UP”.  
– M E N U –  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
B
Make sure ...  
Press the POWER button to turn on the TV/VCR.  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
Then press the F.FWD/B button.  
1 Select “CHANNEL SET UP”  
Press the MENU button on the  
remote control.  
– M E N U –  
2 Select “ADD/DELETE CH”  
Press the PLAY/K or STOP/L but-  
ton to point to “ADD/DELETE  
CH”.  
– CHANNEL SET UP –  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
B
ADD / DELETE CH (CATV)  
AUTO CH PROGRAMMING  
B
Press the PLAY/K or STOP/L but-  
ton to point to “CHANNEL SET  
UP”.  
ZERO RETURN  
TIME SEARCH  
Press the F.FWD/B button.  
Then press the F.FWD/B button.  
3 Enter the desired channel number  
Press the PLAY/K or STOP/L but-  
ton until your desired channel num-  
ber appears. (You can also use the  
number buttons or the CHANNEL  
K/L button to enter it) (Example:  
CH8)  
2 Begin auto preset  
– CHANNEL SET UP –  
Press the PLAY/K or STOP/L but-  
ton to point to “AUTO CH PRO-  
GRAMMING”.  
ADD / DELETE CH (CATV)  
AUTO CH PROGRAMMING  
08  
B
ADD / DELETE  
Then press the F.FWD/B button.  
The tuner scans and memorizes all  
the active channels in your area.  
You must precede single-digit channel numbers  
with a zero (Example: 02 ... 09).  
When selecting cable channels which are higher  
than 99, press the +100 button first, then press the  
last two digits. (Example: to select channel 125,  
first press the +100 button then press “2” and “5”).  
3 After scanning  
The tuner stops on the lowest memorized channel.  
When AUTO CH PROGRAMMING is activated  
where there is no TV signal input, “NO TV SIG-  
NALS” will appear on the display after the com-  
pletion of the channel scanning.  
4 Delete (or add) it from (into) memory  
Press the F.FWD/B or REW/s button. The channel  
number changes to light red. The channel is deleted  
from memory.  
To delete another channel, repeat steps [3] and [4].  
If you press the F.FWD/B or REW/s button  
The TV/VCR may recognize TV channels to be  
CATV channels by the receiving conditions. In this  
case, try auto preset again in the fine receiving  
conditions.  
again, the channel is memorized again.  
Added channel: Light blue.  
Deleted channel: Light red.  
5 Exit the channel setup mode  
Press the MENU button on the remote control to  
return to TV mode.  
NOTE: To confirm that channel(s) has been deleted  
or added, press the CHANNEL K or L button.  
- 13 -  
EN  
9I03  
 
TV OPERATION  
WATCHING A TV PROGRAM  
PICTURE CONTROL  
The TV/VCR’s picture controls – BRIGHT, CON-  
TRAST, COLOR, TINT and SHARPNESS – are  
preset to factory specifications. Although they are  
usually the best, you may need to make some further  
adjustments for a more natural looking image.  
NOTES:  
1 Turn on the TV/VCR  
Press the POWER button to turn on the TV/VCR.  
2 Select the channel number  
Press the CHANNEL K or L button to select your  
desired channel number or press the number buttons  
on the remote control.  
Remember: If the TV/VCR is connected to a cable  
box or satellite box, the TV/VCR must be on CH3 or  
CH4, then the channel to be viewed must be selected  
on the cable box or satellite box.  
Procedures must be followed within 5 seconds or  
the Picture Control mode will be cancelled.  
When setting the Picture Control, the Game mode  
will be cancelled.  
Make sure ...  
TV/VCR power must be turned on.  
1 Select “PICTURE CONTROL”  
3 Adjust sound  
Press the VOLUME X or Y button  
to adjust the volume.  
Press the MENU button on the  
– M E N U –  
remote control.  
TIMER PROGRAMMING  
B
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
Press the PLAY/K or STOP/L but-  
ton to point to “PICTURE CON-  
TROL”.  
VOLUME 20  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
C
C
C
C
C
C
C
C
C
C
C
C
TIME SEARCH  
Then, press the F.FWD/B button.  
GAME MODE  
2 Select item you want to adjust  
Press the PLAY/K or STOP/L button until desired  
This function enables you to decrease the TV screen  
contrast and making it suitable for use with a TV  
GAME.  
control is displayed.  
BRIGHT  
CONTRAST  
NOTE: This function can not be set during recording.  
BRIGHT  
COLOR  
P
P
P
P
P
P
P
C
P
P
P
P
P
P
P +  
TINT  
Press the GAME button on the  
GAME  
remote control. “GAME” appears  
on the screen.  
SHARPNESS  
3 Adjust the picture control  
When you press the GAME button;  
Press the F.FWD/B or REW/s button to adjust to  
The TV/VCR comes on automatically if it is off.  
The TV/VCR will be in external input mode auto-  
your desired level.  
matically.  
TO CANCEL THE GAME MODE  
Press the GAME button or CHANNEL K or L but-  
ton on the remote control.  
REW/s  
to decrease  
brightness  
to decrease  
contrast  
F.FWD/B  
to increase  
brightness  
to increase  
contrast  
BRIGHT  
CONTRAST  
DEGAUSSING  
Magnetism from nearby appliances might affect the  
color of the TV picture.  
If this happens, move this unit away from the appli-  
ance. If the color is still not correct, disconnect  
power cord from AC outlet then reconnect it after 30  
minutes.  
COLOR  
TINT  
to pale  
to brilliant  
to purple  
SHARPNESS to soft  
to green  
to clear  
If there is a power failure of any kind, the unit will  
retain its memory for this feature.  
- 14 -  
EN  
9I03  
 
TO CANCEL THE CLOSED CAPTION  
SYSTEM  
CLOSED CAPTION SYSTEM  
You can view specially labeled (cc) TV programs,  
movies, news and pre-recorded tapes with either a  
dialogue caption or text display.  
Repeat steps [1] and [2], select [OFF] using the  
F.FWD/B or REW/s button. Press the MENU but-  
ton on the remote control to return to TV mode.  
CAPTION mode: By choosing the caption mode, you  
can watch dramas, movies and news while captioning  
the dialogues and the contents of news.  
TEXT mode: By choosing the text mode, you can  
watch half screen text information if you want.  
1-2: You may get these captions or text information  
by selecting either “1” or “2”. Caption “2” is used,  
usually for a second language if available.  
WHEN THE CLOSED CAPTION MODE  
IS ON  
The On-Screen Display will disappear after 5 sec-  
onds.  
This is also true when the MUTE button is pressed  
or when the PAUSE/STILL button is pressed while  
recording.  
If there is a power failure of any kind, the unit will  
retain its memory for this feature.  
NOTE:  
Not all programs are broadcast with closed captions.  
Your television is designed to provide error free  
closed captions from high quality antenna, cable and  
VCR signals. Conversely, poor quality signals are  
likely to result in caption errors or no captions at all.  
Common signal conditions which may cause captions  
errors are listed below:  
V-CHIP SET UP  
V-CHIP enables parents to prevent their children  
from watching inappropriate material on TV.  
V-CHIP reads the ratings for programming (except  
for news and sports programs, unedited movies on  
premium cable channels and Emergency Broadcast  
System signals), then denies access to programming  
if the program’s rating meets the limitations you  
select. In this case, “PROTECTED PROGRAM by  
...” message appears on the TV screen.  
To block ratings, follow the steps below.  
Programming may be rated by the Motion Picture  
Association of America (MPAA) or according to  
the Television Parental Guidelines. In order to  
block any inappropriate programming, set your  
limits in both places (MPAA RATING and TV  
RATING).  
Automobile ignition noise  
Electric motor brush noise  
Weak snowy reception on TV screen  
Multiplex signal reception displaying picture  
ghosts or airplane flutter.  
Playback of poorly recorded or worn VCR tapes.  
NOTE:  
If the TV/VCR displays a black box on the TV  
screen, this means that the TV/VCR  
is set to the TEXT mode. To clear  
screen, select [CAPTION1], [CAP-  
TION2] or [OFF].  
Make sure ...  
TV/VCR power must be turned on.  
TV RATING SET UP  
Make sure ...  
– M E N U –  
1 Select “CAPTION”  
TIMER PROGRAMMING  
TV/VCR power must be turned on.  
PICTURE CONTROL  
Press the MENU button on the  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
remote control.  
Press the PLAY/K or STOP/L but-  
ton to point to “CAPTION”.  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
B
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
1 Select “V-CHIP SET UP”  
– M E N U –  
TIMER PROGRAMMING  
Press the MENU button on the  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
remote control.  
USER’S SET UP  
B
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
Press the PLAY/K or STOP/L but-  
ton to point to “V-CHIP SET UP”.  
Then press the F.FWD/B button.  
2 Select your desired caption menu  
Press the F.FWD/B or REW/s  
button until your desired caption  
menu appears.  
([CAPTION1], [CAPTION2],  
[TEXT1] or [TEXT2])  
TIME SEARCH  
– M E N U –  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [CAPTION1]  
ZERO RETURN  
2 Select “TV RATING”  
Press the PLAY/K or STOP/L but-  
ton to point to “TV RATING”.  
Then press the F.FWD/B button.  
B
– V-CHIP SET UP –  
TIME SEARCH  
B
TV RATING  
MPAA RATING  
3 Exit the caption setting mode  
Press the MENU button on the remote control to  
return to TV mode.  
- 15 -  
EN  
9I03  
 
3 Select your desired item  
Press the PLAY/K or STOP/L button to point to  
your desired item.  
4 Exit the V-Chip setting mode  
Press the MENU button on the remote control to  
return to original mode.  
Then, press the F.FWD/B button to  
select [BLOCK] or [VIEW].  
B
TV–Y  
TV–Y7  
TV–G  
TV–PG (  
TV–14  
TV–MA(  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
MPAA RATING SET UP  
(
)
)
)
)
(
Make sure ...  
When you select the rating cate-  
gory and change it to [BLOCK],  
the higher rating will change to  
TV/VCR power must be turned on.  
[BLOCK] automatically. Also, the lower rating will  
change to [VIEW] automatically.  
When you change “TV-Y” to [VIEW], the all rat-  
ings will change to [VIEW] automatically.  
1 Select “V-CHIP SET UP”  
– M E N U –  
Press the MENU button on the  
TIMER PROGRAMMING  
PICTURE CONTROL  
remote control.  
Press the PLAY/K or STOP/L but-  
ton to point to “V-CHIP SET UP”.  
Then press the F.FWD/B button.  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
B
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
Selection  
TV-Y  
Rating Category Explanations  
Appropriate for all children  
TIME SEARCH  
TV-Y7  
TV-G  
TV-PG  
TV-14  
Appropriate for children seven and older  
General Audience  
Parental Guidance suggested.  
Unsuitable for children under 14  
– V-CHIP SET UP –  
2 Select “MPAA RATING”  
Press the PLAY/K or STOP/L but-  
ton to point to “MPAA RATING”.  
Then press the F.FWD/B button.  
B
TV RATING  
MPAA RATING  
TV-MA Mature audience only  
When you select TV-Y7, TV-PG, TV-14 or TV-MA  
and you press the F.FWD/B button, the sub-ratings  
will appear on the TV screen.  
If you select the rating category (example: TV-PG)  
and change it to [BLOCK] or [VIEW], the sub-rat-  
ings (example: V for Violence) will change to  
[BLOCK] or [VIEW] automatically.  
3 Select your desired item  
Press the PLAY/K or STOP/L but-  
ton to point to your desired item.  
Then press the F.FWD/B button to  
select [BLOCK] or [VIEW].  
G
[VIEW]  
PG  
[VIEW]  
PG–13  
R
NC–17  
X
[VIEW]  
B
[BLOCK]  
[BLOCK]  
[BLOCK]  
You can set the sub-ratings to [BLOCK] or [VIEW]  
individually when the rating category is set to  
[BLOCK].  
To set the sub-ratings individually, follow the steps  
below.  
Selection  
G
PG  
PG-13  
R
Rating Category Explanations  
General Audience  
Parental Guidance suggested.  
Unsuitable for children under 13  
Restricted; under 17 requires accompa-  
nying parent or adult guardian  
No one under 17 admitted  
When you select [TV-Y7]:  
TV–Y7  
FV  
[BLOCK]  
[BLOCK]  
Press the STOP/L or PLAY/K  
button to select “FV” (Fantasy  
Violence).  
B
NC-17  
X
Mature audience only  
Then press the F.FWD/B button  
to select [BLOCK] or [VIEW].  
When you select the rating category and change it  
to [BLOCK], the higher rating will change to  
[BLOCK] automatically. Also, the lower rating  
will change to [VIEW] automatically.  
When you change “G” to [VIEW], all ratings will  
change to [VIEW] automatically.  
When you select [TV-PG], [TV-14] or [TV-MA]:  
Press the STOP/L or PLAY/K  
button to select “D”(Suggestive  
Dialog), “L”(Coarse Language),  
“S”(Sexual Situation) or  
TV–PG  
[BLOCK]  
B
D
L
S
V
[BLOCK]  
[BLOCK]  
[BLOCK]  
[BLOCK]  
“V”(Violence). Then press the  
F.FWD/B button to select  
[BLOCK] or [VIEW].  
Note: When you select [TV-MA], “D” does not  
appear on the TV screen.  
4 Exit the V-Chip setting mode  
Press the MENU button on the remote control to  
return to original mode.  
The sub-ratings which set to  
B
TV–Y  
TV–Y7  
TV–G  
TV–PG (DLSV)  
TV–14 (DLSV)  
TV–MA ( LSV)  
[VIEW]  
(
)
[VIEW]  
[VIEW]  
[BLOCK] appears next to the rat-  
ing category in the TV RATING  
menu.  
[BLOCK]  
[BLOCK]  
[BLOCK]  
- 16 -  
EN  
9I03  
 
PLAYBACK  
This TV/VCR will operate with any cassette that has the  
mark. For best results, we  
recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.  
INSERTING A CASSETTE  
Insert the cassette in the direction as shown. Push in  
gently, but continuously, on the center-back of the  
cassette until it is drawn into the TV/VCR. The  
TV/VCR will automatically turn on.  
AUTO REPEAT PLAYBACK  
The TV/VCR has the auto repeat function that allows  
you to repeat a tape indefinitely without touching the  
PLAY button.  
ALL REPEAT: Repeat playback from the beginning  
to the end of the tape.  
BLANK REPEAT: Repeat playback from the begin-  
ning to a blank part, which is blank for more than  
10 seconds.  
Window  
WRONG  
CORRECT  
1 Select “USER’S SET UP”  
PRECAUTIONS  
– M E N U –  
Press the MENU button on the  
TIMER PROGRAMMING  
PICTURE CONTROL  
Avoid moisture. Moisture condensation may occur  
on the tape if it is moved from a cold place to a  
warm place or visa versa. Before using a tape with  
these conditions, to avoid damage of the tape and  
your TV/VCR, wait until the tape has warmed to  
room temperature and the moisture has evaporated.  
Avoid extreme heat, high humidity and magnetic  
fields.  
remote control.  
SETTING CLOCK  
CHANNEL SET UP  
B
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
Press the PLAY/K or STOP/L but-  
ton to point to “USER’S SET UP”.  
Then press the F.FWD/B button.  
2 Select “ALLor “BLANK”  
Press the PLAY/K or STOP/L button to point to  
“REPEAT PLAY”.  
Press the F.FWD/B or REW/s  
button repeatedly until your desired  
selection [ALL] or [BLANK]  
appears.  
Do not tamper with the cassette mechanism.  
Do not touch the tape with your fingers.  
USER’S SET UP  
RENTAL  
REPEAT PLAY  
AUTO RETURN  
[OFF]  
[ALL]  
[OFF]  
B
NORMAL PLAYBACK  
Make sure ...  
TV/VCR power must be turned on.  
3 Exit the Repeat Play setting  
Press the MENU button on the remote control to  
return to the TV mode.  
1 Insert a prerecorded tape  
If the erase-protection tab has been removed, the  
TV/VCR will start playback automatically.  
4 Start playback  
Press the PLAY button to start the Repeat Play.  
“REPEAT PLAY B” appears.  
B
PLAY  
2 To begin playback  
Press the PLAY button.  
Once you select the Repeat Play mode, it stays in  
effect even after you turn off the TV/VCR.  
If the Rental mode is set [ON], the “RENTAL  
PLAY B” display has priority.  
Note: If any menu is activated on  
the screen, the PLAY button does  
not function. Press the MENU but-  
ton to clear the menu. then, press  
the PLAY button.  
STOP  
3 To stop playback  
Press the STOP button when play-  
back is completed.  
TO CANCEL THE REPEAT PLAY MODE  
Repeat steps [1] and [2], select [OFF] using the  
F.FWD/B or REW/s button on the remote control.  
Press the MENU button on the remote control to  
return to TV mode.  
If there is a power failure of any kind, the unit  
will retain its memory for this feature.  
- 17 -  
EN  
9I03  
 
NOTES:  
SEARCH  
Time Search can be set up to a maximum of 9  
hours 50 minutes (9:50) by 10 minutes at a time.  
PICTURE SEARCH  
This feature is very useful in finding or skipping over  
a particular scene on a tape. In this mode, the sound  
will be muted.  
This function will not operate in recording mode.  
In the example below: To watch a program after 2  
hour 50 minutes from the present position, in either  
direction.  
1) You may view a video tape at a high speed in  
either a forward or reverse direction by pressing  
the F.FWD/B or REW/s button during playback.  
(in the SP / LP / SLP modes)  
2) Press it again and the TV/VCR will now search in  
super high speed. (in the LP / SLP modes only)  
NOTE: Tapes recorded in the SP or LP mode will  
display a noise bar on the TV screen and the picture  
may revert to Black and White. This is normal.  
3) Press the PLAY/K button to return to normal  
speed.  
1 Insert a tape.  
2 Select “TIME SEARCH” mode  
Press the TIME SEARCH button (with each push it  
will increase by 10 minute).  
3 Enter your desired time  
Press the PLAY/K or STOP/L but-  
ton until your desired time appears.  
(Example: “2:50” stands for 2 hours  
50 minutes)  
If you wish to cancel the Time Search at this point,  
press the MENU button on the remote control.  
TIME SEARCH  
2 : 50  
ZERO RETURN  
This function allows you to search easily a beginning  
point that you want to review by rewinding or fast  
forwarding.  
NOTE:  
4 Begin Time Search  
Zero Return WILL NOT work on a blank tape or a  
blank portion of a tape.  
By pressing the REW/s or F.FWD/B button, the  
TV/VCR will rewind or fast forward to the specified  
point.  
1 Stop a tape at your desired point  
Rewind or fast forward the tape to the beginning  
point at which you want to review.  
The time counts down as the searching progresses.  
When 0:00 is reached, the tape will start playback  
automatically.  
2 Reset the counter to 0:00:00  
Press the COUNTER RESET button repeatedly.  
TO CANCEL THE TIME SEARCH at this  
point  
Press the STOP/EJECT button on the TV/VCR or the  
remote control. This will delete the selected time.  
3 Begin recording or playback  
Press the RECORD or PLAY button.  
Press the STOP button when recording or playback is  
completed.  
STILL PICTURE  
You can view a still picture on the TV screen during  
playback (the Still mode). Press the PAUSE/STILL  
button during playback. Only tapes recorded in the  
SLP mode will show the least amount of lines. Press  
the PLAY button to return to playback.  
NOTES:  
4 To activate “ZERO RETURN” mode  
Press the MENU button on the remote control.  
Press the PLAY/K or STOP/L button to point to  
“ZERO RETURN”.  
– M E N U –  
TIMER PROGRAMMING  
Then press the F.FWD/B button.  
PICTURE CONTROL  
Usually there will be video “noise” lines (black  
and white streaks or dots) on the screen. This is  
normal.  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
The counter will appear on the TV  
screen.  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
B
The tape will automatically stop  
when the counter returns to 0:00:00.  
TIME SEARCH  
If the tape was originally recorded in SP or LP  
mode, the still picture will be black and white in  
addition to the “noise” lines.  
This is not a fault of the machine, but is a by-  
product of the technology involved in producing  
a TV/VCR with 2 video heads.  
TIME SEARCH  
The Time Search function makes it possible to  
quickly advance the tape to your desired position  
simply by entering the exact amount of playback  
time you want to skip.  
If it is left in the Pause mode for more than five  
minutes, the TV/VCR will automatically switch to  
the Stop mode.  
- 18 -  
EN  
9I03  
 
NOISE CANCEL (in the Still mode)  
RENTAL PLAYBACK  
This feature allows you to reposition or reduce the  
noise lines of a still picture. Press the PAUSE/STILL  
button so that the noise lines change position on the  
screen so you can see the picture in its entirety with-  
out distracting noise lines.  
NOTE: This feature can be activated ONLY when  
viewing a tape recorded in the SLP mode. If the tape  
was originally recorded in the SP or LP mode, the  
still picture may revert to black and white in addition  
to the “noise bars”. This is normal.  
This function enables you to improve the picture  
quality when playing back worn cassettes such as  
rented tapes.  
1 Select “USER’S SET UP”  
– M E N U –  
TIMER PROGRAMMING  
Press the MENU button on the  
PICTURE CONTROL  
SETTING CLOCK  
remote control.  
CHANNEL SET UP  
B
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
Press the PLAY/K or STOP/L but-  
ton to point to “USER’S SET UP”.  
Then press the F.FWD/B button.  
VERTICAL HOLD CONTROL  
If the picture begins to vibrate vertically while in  
Pause/Still mode, stabilize the picture by pressing the  
CHANNEL K or L button.  
USER’S SET UP  
2 Set “RENTALto [ON]  
Press the PLAY/K or STOP/L but-  
ton to point to “RENTAL”.  
Press the F.FWD/B or REW/s  
button until [ON] appears.  
B
RENTAL  
REPEAT PLAY  
AUTO RETURN  
[ON]  
[OFF]  
[OFF]  
NOTE:  
If there are video noise lines on the screen, reposition  
or reduce them. Refer to “NOISE CANCEL”.  
3 Exit the Rental setting  
Press the MENU button on the remote control to  
return to the TV mode.  
PICTURE CONTROLS  
TRACKING ADJUSTMENT  
4 Start playback  
Tracking adjustment will be set automatically  
(Digital Tracking function) when you start play-  
back.  
Press the PLAY button to start playback. “RENTAL  
PLAY B” appears.  
Once you select the Rental mode, it stays in effect  
even after you turn off the TV/VCR.  
However when playing pre-recorded tapes or tapes  
recorded on units other than your own, noise lines  
(black and white streaks) may appear on the play-  
back picture. If this occurs, you can adjust the  
tracking control manually by pressing the CHAN-  
NEL K or L button until the streaks disappear. To  
return to the DTR function, stop the tape once and  
start playback again.  
TO CANCEL THE RENTAL MODE  
Repeat steps [1] and [2], select [OFF] using the  
F.FWD/B or REW/s button on the remote control.  
Press the MENU button on the remote control to  
return to TV mode.  
If there is a power failure of any kind, the unit  
will retain its memory for this feature.  
RECORDING  
TWO DIFFERENT TAPE SPEEDS  
ERASE PREVENTION  
Before recording, select the tape speed from : SP  
mode (Standard Play) or SLP mode (Super Long  
Play).  
The table below shows the maximum recording/play-  
back time using T60, T120 or T160 tapes in each  
mode.  
You can prevent accidental  
erasing of recording by  
breaking off the tab on the  
back edge of the cassette.  
Tab  
Tape Speed  
Type of tape  
SP mode  
Recording/Playback Time  
If you decide to record on  
the tape again, cover the  
hole with plastic tape.  
T60  
1 hour  
3 hours  
T120  
T160  
2 hours 2-2/3 hours  
6 hours 8 hours  
SLP mode  
Note: You can playback a tape recorded in LP mode  
(Long Play).  
Plastic Tape  
- 19 -  
EN  
9I03  
 
Make sure ...  
TV/VCR power must be turned on.  
Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to  
the point at which you want to begin recording.)  
NOTE: This unit will ONLY record and view the same channel.  
NORMAL RECORDING  
OTR (One Touch Recording)  
You can ONLY watch the same TV program that is  
being recorded.  
This function enables you to set a recording length  
simply by pressing the REC/OTR button on the  
TV/VCR.  
Make sure ...  
1 Select the channel to be recorded  
TV/VCR power must be turned on.  
Insert a cassette tape with its erase prevention tab  
Press the number buttons on the  
CH 10  
remote control or the CHANNEL  
K or L button.  
in place. (If necessary, rewind or fast forward the  
Remember: If the TV/VCR is con-  
nected to a cable box or satellite  
box, the TV/VCR must be on CH3  
or CH4, then the channel to be recorded must be  
selected on the cable box or satellite box.  
tape to the point at which you want to begin  
recording.)  
NOTES:  
You cannot start OTR with the remote control.  
Recording starts immediately when the REC/OTR  
button is pressed.  
2 Select the tape speed  
Press the SPEED button to select  
the desired tape speed (SP/ SLP).  
When the REC/OTR button is pressed 18 times, the  
TV/VCR returns to the Normal Recording mode.  
To stop the OTR operation, press the STOP button  
on the TV/VCR or on the remote control.  
SP  
To show the remaining time, press the DISPLAY  
button on the remote control so that “OTR”  
appears on the TV screen. (It will show up momen-  
tarily then disappear.)  
REC  
3 Begin recording  
Press the RECORD button.  
Recording stops when 0:00 is reached.  
Please note that in the SLP mode maximum record-  
ing time, assuming the tape is started at the begin-  
ning, is 8 hours using T-160 (or 6 hours using T-120).  
SP  
If the tape runs out before the end time, the  
TV/VCR will switch to the Stop mode immediate-  
ly, ejects the tape and turns itself off.  
4 Stop recording  
Press the STOP button when recording is completed.  
If you press the power button during OTR, the  
TV/VCR continues recording until the selected  
length is reached.  
SKIPPING UNWANTED  
SCENES DURING RECORDING  
Press the PAUSE/STILL button to  
temporarily stop recording.  
Press the PAUSE/STILL or  
RECORD button to resume record-  
ing.  
PAUSE  
1 Select the channel to be recorded  
Press the number buttons on the remote control or the  
CHANNEL K or L button.  
Remember: If the TV/VCR is connected to a cable  
box or satellite box, the TV/VCR must be on CH3 or  
CH4, then the channel to be recorded is selected on  
the cable box or satellite box.  
SP  
NOTES:  
After five minutes, the TV/VCR will automatically  
switch to the Recording mode to prevent tape dam-  
age.  
2 Select the tape speed  
Press the SPEED button to select the desired tape  
speed (SP/ SLP).  
If “CLOSED CAPTION (ON)” is selected, the On-  
Screen Display will appear for 5 seconds, then dis-  
appear.  
- 20 -  
EN  
9I03  
 
Avoid overlap of programs ...  
There is a chance that a program will not be recorded  
when programs overlap;  
3 Begin OTR  
OTR(2 : 30)  
Press the REC/OTR button on the  
TV/VCR as many times as needed.  
The recording length will be deter-  
mined by the number of times you  
press the REC/OTR button. Each  
The program with an earlier start has priority.  
Once the earliest program finishes, the overlapping  
programs will begin recording in sequence.  
SP  
The illustration below demonstrates the sequence  
of recordings.  
additional push will increase the recording time by  
30 minutes. It is set up to 8 hours.  
Recording Sequence  
Program 1  
10:00AM-11:00AM  
Program 2  
9:00AM-10:00AM  
Program 3  
Push(es) Display  
1 push  
Recording length  
(normal recording)  
2 pushes  
3 pushes  
0:30  
1:00  
30 minutes  
60 minutes  
9:30AM-12:00PM  
9:00AM  
10:00AM  
11:00AM  
12:00PM  
*Recording period is SHADED  
17 pushes  
8:00  
480 minutes  
1 Select “TIMER PROGRAMMING”  
Press the MENU button on the  
remote control.  
Confirm “TIMER PROGRAM-  
MING” is pointed by pressing the  
PLAY/K button, then press the  
F.FWD/B button.  
– M E N U –  
TIMER RECORDING  
B
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
You may set the TV/VCR to start and end a record-  
ing while you are away. You can set 8 programs to  
record on specific days, daily or weekly within a 1  
year period.  
In the example below, the timer is being set to record:  
July 4th, 2004  
SETTING TIME: from 7:30PM to 8:50PM  
ZERO RETURN  
TIME SEARCH  
If you have not yet set the clock, “MANUAL  
CLOCK SET” appears. If so, follow steps [3] to  
[8] on page 11. Then set the timer recording.  
DATE:  
CHANNEL:  
TAPE SPEED:  
CH61  
SP  
2 Select your desired program position (1~8)  
– TIMER PROGRAMMING –  
Press the PLAY/K or STOP/L but-  
ton to select the desired program  
position.  
CH DATE  
BEGIN END  
Make sure ...  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
If a cable box or satellite box is connected with the  
TV/VCR you will be limited to record only one  
channel, and the channel selector on the TV/VCR  
must be selected to the output channel of the boxes  
CH 3 or CH 4 and then the actual channel to be  
recorded must be selected on the boxes.  
Clock must be set to the correct time and date  
before setting the timer.  
TV/VCR power must be turn on to program it.  
Insert a cassette tape with its erase prevention tab  
in place. (If necessary, rewind or fast forward the  
tape to the point at which you want to begin  
recording.)  
B
Then press the F.FWD/B button.  
3 Set the channel number  
Press the PLAY/K or STOP/L but-  
ton until the desired channel num-  
ber appears.  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
B
(Example: CH61)  
Then press the F.FWD/B button.  
Remember: If the TV/VCR is connected to a cable  
box or satellite box, the TV/VCR must be on CH3 or  
CH4, then the channel to be recorded is selected on  
the cable box or satellite box.  
The channel you want to record is properly set in  
advance.  
4 Select once, every day or weekly recording  
For once recording :  
– TIMER PROGRAMMING –  
CH DATE  
BEGIN END  
Press the PLAY/K (up) button  
until the desired date appears.  
(Example: “7/04” for July 4th).  
Then press the F.FWD/B button.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 7/04 SUN -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
B
- 21 -  
EN  
9I03  
 
For every day recording : To record a TV program at  
the same time on the same channel every day.  
(Example: Monday through Sunday)  
10 Finish setting the program  
Press the F.FWD/B or REW/s button. The program  
is now completed.  
– TIMER PROGRAMMING –  
Press the STOP/L (down) button  
CH DATE  
BEGIN END  
To set another program, repeat steps [2] to [10].  
Press the MENU button on the remote control to  
until “EVRY DAY” appears.  
Then press the F.FWD/B button.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 EVRY DAY -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
B
return to original mode.  
11 Set the timer  
For weekly recording : To record a TV program at  
Press the POWER button to set automatic timer  
recording. The RECORD indicator lights up.  
the same time on the same channel every week.  
(Example: every Monday)  
– TIMER PROGRAMMING –  
CH DATE  
BEGIN END  
You must turn off the TV/VCR to activate automat-  
ic timer recording.  
Press the STOP/L (down) button  
until “EVRY” and your desired  
day of the week appear together.  
Then press the F.FWD/B button.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
61 EVRY MON -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
B
If power is not turned off and you continue watch-  
ing TV, TIMER REC STANDBY” starts flashing  
on the TV screen 2 minutes before the programmed  
start time.  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
5 Set beginning hour  
Press the PLAY/K or STOP/L but-  
ton until the desired hour appears.  
(Example: “7, PM” for 7:30PM)  
Then press the F.FWD/B button.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
TIMER PROGRAM EXTENSION  
61 7/04 SUN 7:12P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
To shift the time schedule of an automatic timer  
recording.  
1) Press the POWER button.  
2) Repeat step [1] on page 21.  
3) Press the RECORD button and select the desired  
program using the PLAY/K or STOP/L button.  
4) Press the RECORD button again.  
6 Set beginning minute  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
Press the PLAY/K or STOP/L but-  
ton until the desired minute appears.  
(Example: “30” for 7:30PM)  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/04 SUN 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
Then press the F.FWD/B button.  
Each additional push will shift forward the  
begin/end time for recording by 10 minutes. When  
the recording is already in progress, each addition-  
al push will shift forward the end time only. If you  
want to cancel while setting, press the  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
7 Set end hour  
Press the PLAY/K or STOP/L but-  
ton until the desired hour appears.  
(Example: “8, PM” for 8:50PM)  
Then press the F.FWD/B button.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/04 SUN 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
8:30P  
M
B
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - - -  
PAUSE/STILL button on the remote control. The  
recording time returns to the original time.  
NOTE: When you shift forward the time schedule  
during recording, the recording speed will automati-  
cally be set to the SLP mode.  
5) Press the F.FWD/B or REW/s button to exit the  
setting menu. Then press the MENU button on the  
remote control to return to original mode.  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
8 Set end minute  
Press the PLAY/K or STOP/L but-  
ton until the desired minute appears.  
(Example: “50” for 8:50PM)  
Then press the F.FWD/B button.  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
61 7/04 SUN 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
8:50P  
M
B
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
TO CORRECT A PROGRAM  
– TIMER PROGRAMMING –  
CH DATE BEGIN END  
9 Set the tape speed  
Press the PLAY/K or STOP/L but-  
ton until the desired tape speed  
appears. (Example: SP)  
While setting a program; press the REW/s but-  
ton to go back one step and enter the correct num-  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
-:- - - -  
-:- - - -  
-:- - - -  
8:50PMSP  
-:- - - -  
-:- - - -  
-:- - - -  
-:- - - -  
bers using the PLAY/K or STOP/L button.  
61 7/04 SUN 7:30P  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
- - -/- - - - - -:- -  
M
B
After setting a program;  
1) Press the POWER button.  
2) Repeat steps [1] - [2] on page 21.  
3) Press the F.FWD/B button (or press the  
REW/s button to go back one step) until the  
part you want to correct begins flashing, then  
make the changes pressing the PLAY/K or  
STOP/L button.  
4) Press the POWER button to set automatic timer  
recording.  
- 22 -  
EN  
9I03  
 
TO CANCEL AN AUTOMATIC TIMER  
RECORDING  
USER’S SET UP  
2 Set “AUTO RETURN” to [ON]  
Press the PLAY/K or STOP/L but-  
ton to point to “AUTO RETURN”.  
Press the F.FWD/B or REW/s  
button until [ON] appears.  
RENTAL  
REPEAT PLAY  
AUTO RETURN  
[OFF]  
[OFF]  
[ON]  
B
After setting a program;  
1) Press the POWER button.  
2) Repeat steps [1] - [2] on page 21 and select a  
program you want to cancel.  
3) Press the T-PROG. CLEAR button.  
4) Press the MENU button on the remote control  
to return to TV mode.  
3 Auto Return will begin  
When all the timer recordings are completed, the  
TV/VCR will rewind to the beginning of the recorded  
While recording is in progress;  
1) Press POWER button.  
program(s).  
NOTE:  
2) Press the STOP/EJECT button on the TV/VCR.  
If you press the POWER button while tape is  
rewinding, the Auto Return will stop.  
TO CHECK THE BEGIN/END TIME  
4 Watch the recorded program  
Press the PLAY/K button.  
1) Press the POWER button so that the Recording  
indicator goes off.  
2) Press the MENU button on the remote control.  
3) Confirm “TIMER PROGRAMMING” is pointed.  
4) Press the F.FWD/B button. The details of pro-  
grams appear on the TV screen.  
5) Press the MENU button on the remote control to  
return to TV mode.  
TO CANCEL THE AUTO RETURN  
MODE  
Repeat steps [1] and [2], select [OFF] using the  
F.FWD/B or REW/s button.  
If there is a power failure of any kind, the unit  
will retain its memory for this feature.  
HINTS FOR AUTOMATIC  
TIMER RECORDING  
WAKE UP TIMER  
The Wake Up Timer function turns on the TV/VCR  
without using the POWER button after a desired  
period of time.  
Make sure the channel you want to record is prop-  
erly set in advance.  
It is not necessary to press the RECORD button for  
timer recording.  
Recording begins automatically at the Start time.  
If you are recording using a Timer mode, you may  
not operate the unit manually.  
The erase-prevention tab on the cassette must be in  
place (or you must put tape over the hole).  
If the erase-prevention tab is removed, the cassette  
will be ejected when the POWER button is pressed  
to off.  
NOTES:  
Use the remote control for this procedure.  
Clock must be set to the correct time before setting  
the timer.  
If you want to select [TAPE], you must insert a  
cassette tape in the TV/VCR. The tape will start  
playback automatically on your desired time.  
If the tape runs out before the end time, the  
TV/VCR will switch to the Stop mode immediately  
and the tape will be ejected.  
1 Select “WAKE-UP TIMER”  
Press the WAKE UP/SLEEP button  
on the remote control once, and  
confirm “ON/OFF” is pointed.  
AUTO RETURN  
WAKE UP B ON/OFF  
[ON]  
TIMER  
TV/TAPE  
TIME  
[TV]  
Press the F.FWD/B or REW/s  
[12:00AM]  
button until [ON] appears.  
With this feature, after timer recording is finished,  
the beginning of the recorded program(s) can be  
searched for automatically.  
2 Select “TV” or “TAPE”  
Press the PLAY/K or STOP/L but-  
ton until to point to “TV/TAPE”.  
Press the F.FWD/B or REW/s  
button and select [TV] or [TAPE].  
– M E N U –  
1 Select “USER’S SET UP”  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
ZERO RETURN  
TIME SEARCH  
Press the MENU button on the  
WAKE UP  
TIMER  
ON/OFF  
B TV/TAPE  
TIME  
[ON]  
B
remote control.  
[TV]  
[12:00AM]  
Press the PLAY/K or STOP/L but-  
ton to point to “USER’S SET UP”.  
Then press the F.FWD/B button.  
- 23 -  
EN  
9I03  
 
3 Set wake up time  
1 Select “SLEEP TIMER”  
Press the PLAY/K or STOP/L but-  
ton until to point to “TIME”.  
Press the F.FWD/B or REW/s  
button until your desired wake up  
time appears.  
Press the WAKE UP/SLEEP button on the remote  
control until “SLEEP TIMER” appears.  
WAKE UP  
TIMER  
ON/OFF  
[ON]  
2 Set sleep time  
Press the PLAY/K, STOP/L,  
F.FWD/B or REW/s button until  
your desired sleep time appears.  
TV/TAPE  
[TV]  
B TIME  
[12:00AM]  
Each additional push will increase (or decrease) the  
time by 10 minutes.  
SLEEP TIMER [2:00]  
Each additional push will increase  
4 Exit the Wake Up Timer setting  
Press the MENU button on the remote control to  
return to TV mode.  
the time by 30 minutes up to 120 minutes.  
Press the MENU button on the remote control to exit  
the Sleep Timer setting.  
TO CANCEL THE WAKE UP TIMER  
TO CANCEL THE SLEEP TIMER  
Repeat step [1] but select [OFF].  
Press the WAKE UP/SLEEP button on the remote  
control until “SLEEP TIMER” appears.  
To view the time left for sleep timer press the WAKE  
UP/SLEEP button twice, then press the MENU but-  
ton on the remote control to exit the sleep timer set-  
ting.  
SLEEP TIMER  
The Sleep Timer function turns off the TV/VCR  
without using the POWER button after a desired  
period of time.  
NOTE:  
This function does not operate during Recording  
mode.  
COPYING A VIDEO TAPE  
You can make copies of video tapes made by friends  
or relatives for your enjoyment.  
1) Insert a pre-recorded video cassette into the  
source (Playing) VCR or camcorder.  
2) Insert a blank video cassette or one you want to  
record over, into the TV/VCR’s cassette compart-  
ment.  
3) Press the SPEED button on remote control for the  
TV/VCR to select the desired recording speed  
(SP/SLP).  
WARNING: Unauthorized recordings of  
copyrighted video tapes may be an  
infringement of copyright laws.  
Connect your TV/VCR and a Source (Playing) VCR  
using the following diagram.  
4) Press the CHANNEL K or L button on the  
TV/VCR until “AUX” appears on the screen.  
NOTE: “AUX” is found below the lowest memo-  
rized channel. (Example: CH2)  
VIDEO  
AUDIO  
[The TV/VCR]  
5) Press the REC/OTR button on the TV/VCR.  
6) Begin playback of the tape in the source (Playing)  
VCR or camcorder.  
NOTE: For best results during dubbing, use the  
TV/VCR’s front panel controls whenever possible.  
The remote control might affect the source (Playing)  
VCR’s playback operation.  
[Ex: Source (playing)  
VCR or camcorder]  
7) To stop copying, press the STOP/EJECT button  
on the TV/VCR, then stop the tape on the source  
VCR or camcorder.  
AUDIO  
Audio/Video  
adapter cable  
(not supplied)  
OUT  
IN  
VIDEO  
- 24 -  
EN  
9I03  
 
ON SCREEN DISPLAY  
To check the Counter, Clock, and Channel number on the TV screen, press the DISPLAY button on the remote  
control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:  
WHEN THE CLOSED CAPTION MODE IS OFF:  
<Off mode>  
<Counter mode>  
<Clock mode>  
Counter mode: After 5 seconds, only  
the counter remains. To clear it, press  
the DISPLAY button.  
Clock mode: After 5 seconds, only  
the clock and the channel number  
remain. To clear them, press the DIS-  
PLAY button.  
5:40PM  
CH2  
Press  
once  
Press  
once  
COUNT 0:12:34  
Press once  
WHEN THE CLOSED CAPTION MODE IS ON:  
OFF mode  
Clock/Counter mode  
The On Screen Display disappear after 5 seconds.  
STOP  
5:40 PM  
CH2  
This is true even if the MUTE button is pressed or the  
PAUSE/STILL button is pressed while recording.  
SP  
COUNT 0:12:34  
SPECIAL FEATURES  
REAL TIME TAPE COUNTER  
AUTO REWIND-EJECT  
This shows the elapsed recording or playback time in  
hours, minutes and seconds. (The displayed time will  
not change on a blank tape or blank portions on the  
tape.)The “–” indication will appear when the tape  
has rewound further than “0:00:00” on the tape  
counter.  
When the end of a tape is reached during record-  
ing, playback or fast-forward, the tape will auto-  
matically rewind to the beginning. After rewinding  
finishes, the TV/VCR will eject the tape and turn  
itself to off.  
This function is operative when Repeat Play is set  
to the [OFF] position.  
The tape will not auto-rewind during timer record-  
ing or One Touch Recording.  
MAINTENANCE  
back, the video heads in your TV/VCR may need  
to be cleaned.  
CABINET CLEANING  
Wipe the front panel and other exterior surfaces of  
the TV/VCR with a soft cloth immersed in luke-  
warm water and wrung dry.  
1. Please visit your local Audio/Video store and pur-  
chase a good quality VHS Video Head Cleaner.  
2. If a Video Head Cleaner does not solve the prob-  
lem, please call our help line at 1-800-968-3429,  
to locate an Authorized Service Center.  
NOTES:  
Remember to read the instructions included with  
the video head cleaner before use.  
Clean video heads only when problems occur.  
Never use a solvent or alcohol. Do not spray insec-  
ticide liquid near the TV/VCR. Such chemicals  
may cause damage and discoloration to the  
exposed surfaces.  
AUTO HEAD CLEANING  
Automatically cleans video heads as you insert or  
remove a cassette, so you can see a clear picture.  
SERVICING  
Should your TV/VCR become inoperative, do not  
try to correct the problem by yourself. There are no  
user-serviceable parts inside. Turn off, unplug the  
power cord and please call our help line at 1-800-  
968-3429, to locate an Authorized Service Center.  
Playback picture may become blurred or interrupt-  
ed while the TV program reception is clear. Dirt  
accumulated on the video heads after long periods  
of use or the usage of rental or worn tapes can  
cause this problem.  
If a streaky or snowy picture appears during play-  
- 25 -  
EN  
9I03  
 
TROUBLESHOOTING GUIDE  
If you have followed the instructions contained in this manual, and have difficulty operating your TV/VCR,  
locate the PROBLEM in the left column below. Check the corresponding CORRECTIVE ACTION column to  
remedy the problem.  
PROBLEM  
CORRECTIVE ACTION  
Make sure the AC cord is connected to an AC outlet.  
Make sure the power is turned on.  
Make sure the AC cord is connected to an AC outlet.  
Check antenna connection.  
Let the TV/VCR program its tuner memory.  
Adjust direction or replace antenna.  
Adjust picture controls.  
Adjust volume control on remote control or main unit.  
Press the MUTE button to restore sound.  
Make sure the timer recording is set correctly.  
Make sure the power is off.  
Make sure the TV/VCR clock is set correctly.  
Make sure the tape has an erase-prevention tab. If needed, cover the  
hole with plastic tape.  
No power.  
No picture and sound.  
No picture or poor picture on  
TV/VCR.  
No sound or poor sound.  
Timer recording is not possible.  
Cannot go into Record mode.  
Playback picture is partially noisy.  
Adjust tracking control for a better picture using the CHANNEL  
or L button on the TV/VCR.  
Head cleaning may be necessary. Refer to “AUTO HEAD  
CLEANING” on page 25.  
K
No picture but the audio is OK in  
playback.  
No operation by infrared Remote  
Control.  
Video or color fades in and out  
when making a copy of a video tape  
Different color marks on screen.  
Make sure the AC cord is connected to an AC outlet.  
Check batteries in remote control.  
You can not copy a copyrighted video tape. You are experiencing  
copy guard protection.  
Magnetism from nearby appliances and geomagnetism might affect  
the color of the TV picture. Move the TV/VCR away from the appli-  
ances, the TV/VCR can repair itself automatically. If you want to  
repair immediately, unplug the TV/VCR power cord, then plug it in  
again 30 minutes or so later.  
.
CLOSED CAPTION PROBLEM  
My TV/VCR is showing captions  
that are misspelled.  
POSSIBLE REMEDY  
You are watching a live broadcast and spelling errors made by the  
closed captioning production company may pass through uncorrected.  
A prerecorded program will not show any misspelled words because  
of the normal time available for editing the captions.  
My TV/VCR will not show the text • Captions that are delayed a few seconds behind the actual dialogue  
in its entirety or there is a delay of are common for live broadcast. Most captioning production companies  
what is being said.  
can display a dialogue to a maximum of 220 words per minute. If a  
dialogue exceeds that rate, selective editing is used to insure that the  
captions remain up-to-date with the current TV screen dialogue.  
• Interference caused by building, power lines, thunderstorms, etc.  
may cause scrambled or incomplete captions to appear.  
My captions are scrambled with  
white boxes on the TV screen.  
My program guide listed a TV show • Broadcasters may at times use a time compression process to speed  
as being closed captioned but none up the actual program so that additional advertising time can be  
of the captions were displayed.  
given. Since the decoder cannot read the compressed information,  
captions will be lost.  
My prerecorded video tape does not • The video tape was either an illegal copy or the tape duplicating  
show any captions. The tape box company accidentally left out the captioning signals during the  
mentions it being closed captioned. copying process.  
My TV screen shows a black box  
on certain channels.  
You are in the TEXT mode. Select CAPTION mode to CAPTION  
[OFF].  
- 26 -  
EN  
9I03  
 
SPECIFICATIONS  
GENERAL SPECIFICATIONS  
ELECTRICAL SPECIFICATIONS  
CRT :  
13 inch in-line gun, 90˚  
deflection tube  
NTSC-M  
Video input level :  
Audio input level :  
0.5~2.0Vp-p  
-15dBs  
Television system :  
Closed caption system :§15.119/FCC  
Video S/N ratio : More than 46dB  
Audio S/N ratio : More than 43dB  
Video Heads :  
Tape width :  
Tape speed  
SP :  
LP :  
SLP :  
Tuner channel  
TV VHF Low :  
TV VHF High :  
TV UHF :  
CATV  
Rotary two-head  
1/2 inch  
OTHER SPECIFICATIONS  
Power requirement : AC 120V/60Hz  
Power consumption : 60W  
33.40mm/sec.  
16.67mm/sec.  
11.12mm/sec.  
Dimensions :  
H:15-5/16” (389mm)  
W:14-7/16” (367mm)  
D:14-7/8” (377mm)  
23.1bs (10.5kg)  
#2~#6  
#7~#13  
#14~#69  
Weight :  
Designs and specifications are subject to change  
without notice.  
If there is a discrepancy between languages, the  
default language will be English.  
VHF :  
5A  
MID band :  
SUPER band :  
HYPER band :  
Terminals  
A5~A1, A~I  
J~W  
W+1~W+84  
Antenna input :  
VHF/UHF 75 ohms  
unbalanced  
Video input :  
Audio input :  
Earphone :  
RCA connector [ 1  
RCA connector [ 1  
1/8” monaural (3.5 mm)  
CABLE CHANNEL DESIGNATIONS  
If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels  
with letters or letter-number combinations. Please check with your local cable company. The following is a  
chart of common cable channel designations.  
CATV channel  
TV Display  
5A  
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10  
10  
11  
11  
12  
12  
13  
13  
A
B
14  
15  
CATV channel  
TV Display  
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
CATV channel  
R
S
T
U
V
W
W+1  
37  
W+2  
38  
W+3  
39  
W+4  
40  
W+5  
41  
W+6  
42  
W+7  
43  
W+8  
44  
W+9  
45  
TV Display  
31  
32  
33  
34  
35  
36  
CATV channel  
W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24  
46 47 48 49 50 51 52 53 54 55 56 57 58 59 60  
W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39  
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75  
W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54  
TV Display  
CATV channel  
TV Display  
CATV channel  
TV Display  
76  
77  
78  
79  
80  
81  
82  
83  
84  
85  
W+59 W+60 W+61 W+62 W+63 W+64  
100 101 102 103 104 105  
86  
87  
88  
89  
90  
W+55 W+56 W+57 W+58  
A-5  
95  
A-4  
96  
A-3  
97  
A-2  
98  
A-1  
99  
CATV channel  
TV Display  
91  
92  
93  
94  
CATV channel  
W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79  
TV Display  
106  
W+80 W+81 W+82 W+83 W+84  
121 122 123 124 125  
107  
108  
109  
110  
111  
112  
113  
114  
115  
116  
117  
118  
119  
120  
CATV channel  
TV Display  
- 27 -  
EN  
9I03  
 
CONTROLES DE OPERACIÓN Y SUS FUNCIONES  
NOTA:  
No recomendamos utilizar mandos a distancia universales. No todas las funciones pueden ser controladas mediante un  
mando a distancia universal. Si decide utilizar un mando a distancia universal con esta unidad, tenga en cuenta que con el  
número de código dado tal vez no se pueda controlar la unidad. En este caso, póngase en contacto con el fabricante del  
mando a distancia universal.  
VIDEO  
AUDIO  
POWER  
VOLUME  
CHANNEL  
STOP/EJECT REW  
PLAY  
F.FWD  
REC/OTR  
EARPHONE  
13  
1 2  
3
4
5
6
7 8 9  
11 12  
14  
10  
X
Y
)–  
4 Botones de volumen (VOLUME  
/
Ajustan el nivel del volumen.  
5 Botones de canales (CHANNEL K/ L)–  
Púlselos para seleccionar los canales deseados  
para ver o grabar.  
25  
WAKE-UP  
POWER  
/SLEEP  
EJECT  
7
3
CHANNEL  
RETURN  
Se puede mostrar el menú principal en la pantalla  
del televisor pulsando repetidamente este botón  
del televisor/videograbadora.  
1
4
7
2
5
8
3
6
9
24  
15  
Función de seguimiento– Pulse los botones  
para minimizar el ruido de vídeo (líneas o puntos  
en la pantalla) durante la reproducción.  
6 Ventanilla sensora del mando a distan-  
cia– Recibe las señales infrarrojas procedentes  
del mando a distancia.  
7 Botón de expulsión (EJECT)–Púlselo en el  
modo de parada para expulsar la cinta del televi-  
sor/videograbadora.  
CHANNEL  
VOLUME  
5
4
0
+100  
MENU  
DISPLAY  
MUTE  
16  
17  
8
23  
9
PLAY  
10  
REW  
F.FWD  
STOP  
Botón de parada (STOP)– Púlselo para  
detener la cinta.  
Botón L–  
7
SPEED PAUSE/STILL  
RECORD  
22  
21  
11  
18  
T-PROG.  
CLEAR  
GAME  
TIME SEARCH  
Púlselo para seleccionar los modos de ajuste  
desde el menú de la pantalla.  
COUNTER  
RESET  
19  
20  
Púlselo para introducir dígitos cuando establez-  
ca un programa.  
(Por ejemplo: Para ajustar el reloj o establecer un  
programa de temporizador)  
8 Botón de rebobinado (REW)– Púlselo para  
rebobinar la cinta, o para ver la imagen en retro-  
ceso rápido durante el modo de reproducción.  
(Búsqueda con rebobinado)  
1 Toma de entrada de vídeo (VIDEO)–  
Conéctela a la toma de salida de vídeo de su  
videocámara u otra videograbadora.  
2 Toma de entrada de audio (AUDIO)–  
Conéctela a la toma de salida de audio de su  
equipo de audio, videocámara u otra  
videograbadora.  
Botón s–  
Púlselo para seleccionar un modo desde un  
menúparticular.  
(Por ejemplo: IDIOMA o ADJUST DE USER)  
9 Botón de reproducción (PLAY)– Púlselo  
para iniciar la reproducción.  
3 Botón de la alimentación (POWER)–  
Botón K–  
Púlselo para encender y apagar el  
televisor/videograbadora. Púlselo para activar la  
grabación con temporizador.  
Púlselo para seleccionar los modos de ajuste  
desde el menú de la pantalla.  
- 28 -  
ES  
0I29  
 
ANT.  
26  
27  
Púlselo para introducir dígitos cuando establez-  
ca un programa.  
(Por ejemplo: Para ajustar el reloj o establecer  
un programa de temporizador)  
16 Botón de menú (MENU)– Púlselo para visu-  
alizar el menú principal en la pantalla del televi-  
sor.  
17 Botón del visualizador (DISPLAY)–  
Visualiza el contador o el número del canal actu-  
al y la hora actual en la pantalla del televisor.  
18 Botón de velocidad de cinta (SPEED)–  
Púlselo para elegir la velocidad de grabación  
deseada: SP/SLP.  
10 Botón de avance rápido (F.FWD)– Púlselo  
para avanzar rápidamente la cinta, o para ver la  
imagen en avance rápido durante el modo de  
reproducción. (Búsqueda con avance rápido)  
Botón B–  
Cuando establezca un programa (por ejemplo:  
19 Botón T-PROG. CLEAR– Púlselo para cance-  
para ajustar el reloj o para establecer un pro-  
grama de temporizador), púlselo para determi-  
nar su elección y vaya al paso siguiente que  
quiera introducir.  
lar un programa de temporizador.  
Botón de reposición del contador  
(COUNTER RESET)– Púlselo para reponer el  
contador a 0:00:00.  
Púlselo para determinar los modos de ajuste  
20 Botón de juego (GAME)– Establece el modo  
del juego y el modo de entrada externa al mismo  
tiempo.  
21 Botón de búsqueda con tiempo (TIME  
SEARCH)– Púlselo para activar el modo de  
búsqueda con tiempo.  
desde el menú de la pantalla.  
Púlselo para seleccionar un modo desde un  
menúparticular.  
(Por ejemplo: IDIOMA o ADJUST DE USER)  
11 Botón de grabación (REC)– Púlselo para  
iniciar la grabación manual.  
22 Botón de pausa/imagen fija  
(PAUSE/STILL)– Púlselo para detener tempo-  
ralmente la cinta durante la grabación o para ver  
una imagen fija durante la reproducción.  
23 Botón de silenciamiento (MUTE)– Silencia  
el sonido. Púlselo de nuevo para recuperar el  
sonido.  
24 Botón de retorno de canal (CHANNEL  
RETURN)– Púlselo para volver al canal anteri-  
or. Por ejemplo, pulsando una vez este botón, la  
visualización del canal cambiará de 3 (canal  
actual) a 10 (canal anterior), y al pulsarlo por  
segunda vez, el canal cambiará del 10 al 3.  
25 Botón del temporizador despertador/para  
dormir (WAKE-UP/SLEEP)– Ajusta el tem-  
porizador para despertarse/dormir.  
Botón de grabación de un toque (OTR)–  
Activa la grabación de un toque. (Sólo en el tele-  
visor/videograbadora)  
12 Indicador de grabación (RECORD)–  
Parpadea durante la grabación.  
Se enciende en el modo de espera de la  
grabación con temporizador.  
13 Toma de auriculares (EARPHONE)– Para  
conectar los auriculares (no suministrados) y  
escuchar en privado. La toma es mono y tiene un  
tamaño de 1/8”(3.5 mm).  
14 Compartimiento del videocasete  
15 Botones numerados– Púlselos para selec-  
cionar los canales deseados para ver o grabar.  
Para seleccionar canales del 1 al 9, pulse primero  
el botón 0 y luego el botón 1 a 9.  
26 Cordón de alimentación– Conéctelo a la  
toma de CA estándar (120V/60Hz).  
Botón +100– Cuando seleccione canales de  
televisión por cable cuyo número sea superior al  
99, pulse primero este botón, y luego pulse los  
dos últimos dígitos. (Para seleccionar el canal  
125, pulse primero el botón “+100” y luego el  
“2” y el “5”.)  
27 Terminal de antena (ANT.)– Para conectar  
una antena o sistema de televisión por cable.  
- 29 -  
ES  
0I29  
 
CONEXIONES DE ANTENA/CABLE  
Desde el cable coaxil o  
caja de emisiones vía  
satélite de 75 ohm del  
sistema de Cable  
Caja de CATV  
o caja de emi-  
siones vía satélite  
(no incluído)  
Antena combinada de  
VHF/UHF  
(no incluído)  
Antena de varilla UHF/VHF  
(incluído)  
OUT  
IN  
Antena VHF  
(no incluído)  
Antena UHF  
(no incluído)  
Desde el  
sistema de Cable  
o
ANT.  
Combinador de  
VHF/UHF  
(no incluído)  
o
o
ANT.  
o
Cable coaxil  
de 75 ohm (no incluído)  
Cable bifilar plano  
MODO DE ENTRADA EXTERNA  
2 Seleccione “LANGUAGE”  
Pulse el botón MENU en el mando  
a distancia.  
Pulse el botón PLAY/K o STOP/L  
para señalar “LANGUAGE”.  
– M E N U –  
TIMER PROGRAMMING  
PICTURE CONTROL  
SETTING CLOCK  
CHANNEL SET UP  
USER’S SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
Cuando utilice una señal de entrada externa (otra  
videograbadora o una videocámara), conecte los cables  
de salida de audio/vídeo del equipo de reproducción a  
las tomas AUDIO IN/VIDEO IN de su  
televisor/videograbadora. Y luego pulse el botón  
CHANNEL K o L hasta que “AUX” aparezca en la  
pantalla.  
B
ZERO RETURN  
TIME SEARCH  
3
Seleccione “ENGLISH”, “ESPAÑOL” o FRANÇAIS”  
Seleccione “ENGLISH”, “ESPAÑOL” o  
“FRANÇAIS” con el botón F.FWD/B y pulse el  
botón REW/s en el mando a distancia.  
Usted puede programar el temporizador para que explore  
todos los canales que puedan recibirse en su zona.  
SELECCION DE IDIOMA  
4 Salga del modo de idioma  
Pulse el botón MENU en el mando a distancia para  
volver al modo del televisor.  
1 Enchufe el cordón de alimentación  
del televisor/videograbadora  
Enchufe el cordón de alimentación del  
televisor/videograbadora en una toma de  
CA estándar.  
NOTA: Si, por alguna razón, el menú está en español  
o francés, pulse el botón MENU en el mando a dis-  
tancia, pulse el botón PLAY/K para señalar el  
“IDIOMA (ESPAÑOL)” o “LANGAGE  
(FRANÇAIS)”, a continuación, pulse el botón  
F.FWD/B y pulse el botón MENU en el mando a  
distancia.  
NOTA:  
Si aparecen algunas cifras en la esquina  
de la pantalla, pulse el botón POWER sin desench-  
ufar el cordón de alimentación.  
Asegúrese de que ...  
Pulse el botón POWER para encender el televi-  
sor/videograbadora.  
NOTA: Esta función afecta sólo el idioma en el  
menú de la pantalla y no la fuente de audio.  
- 30 -  
ES  
0I29  
 
AJUSTE DE CANAL  
AJUSTE DEL RELOJ  
Puede programar el sintonizador para buscar todos  
los canales que recibe en su localidad.  
Cerciórese...  
La alimentación del televisor/videograbadora  
deberá estar conectada.  
En el ejemplo de abajo, el reloj va a ajustarse así:  
FECHA: 6 de mayo de 2004  
HORA: 5:40 PM  
1) Pulse el botón MENU en el mando a distancia.  
Pulse el botón PLAY/K o STOP/L para indicar  
“AJUSTE RELOJ”.  
Luego, pulse el botón F.FWD/B.  
2) Pulse el botón PLAY/K o STOP/L para indicar  
“AJUSTE MANUAL RELOJ”.  
NOTA: El canal preparado NO es necesario cuando  
esté conectado a una caja de cable o caja de satélite.  
Sólo tiene que seleccionar con el selector de canal  
del televisor/videograbadora al canal de salida de la  
caja de cabe o caja de satélite (por ejemplo el canal  
CH3). Seleccione el canal a ver en la caja de cable o  
caja de satélite.  
Asegúrese de que ...  
Pulse el botón POWER para encender el televi-  
sor/videograbadora.  
Luego, pulse el botón F.FWD/B.  
1 Seleccione “AJUSTE DE CANAL”  
3) Pulse el botón PLAY/K o STOP/L hasta que  
aparezca el mes deseado. (Ejemplo: Mayo - 05)  
Luego, pulse el botón F.FWD/B.  
4) Pulse el botón PLAY/K o STOP/L hasta que  
aparezca el día del mes deseado. (Ejemplo: 6 -  
06)  
Pulse el botón MENU en el mando  
– M E N U –  
COMO PROGRAMAR  
a distancia.  
CONTROL DE IMAGEN  
AJUSTE RELOJ  
B
AJUSTE DE CANAL  
AJUSTE DE USER  
AJUSTE DE V-CHIP  
IDIOMA [ESPAÑOL]`  
TITULO [OFF]  
Pulse el botón PLAY/K o el botón  
STOP/L para señalar “AJUSTE DE  
CANAL”.  
RETORNO A CERO  
BUSQUEDA DE HORA  
A continuación, pulse el botón  
F.FWD/B.  
Luego, pulse el botón F.FWD/B.  
5) Pulse el botón PLAY/K o STOP/L hasta que  
aparezca el año deseado. (Ejemplo: 2004)  
Luego, pulse el botón F.FWD/B.  
6) Pulse el botón PLAY/K o STOP/L hasta que  
aparezca la hora deseada. (Ejemplo: 5, PM)  
Luego, pulse el botón F.FWD/B.  
2 Empiece el prefijado automático  
Pulse el botón PLAY/K o STOP/L  
para señalar “AUTOPROGRAMA-  
AJUSTE DE CANAL  
AGREGAR/BORRAR (CATV)  
B AUTOPROGRAMACION DE CA.  
CION DE CA”.  
7) Pulse el botón PLAY/K o STOP/L hasta que  
aparezca el minuto deseado. (Ejemplo: 40)  
8) Pulse el botón MENU en el mando a distancia.  
Aunque los segundos no se visualizan, éstos  
empiezan a contar desde 00 cuando se pulsa  
MENU en el mando a distancia. Utilice esta fun-  
ción para sincronizar el reloj con la hora correcta.  
A continuación, pulse el botón  
F.FWD/B.  
El sintonizador busca y memoriza todos los canales  
activos en su localidad.  
3 Después de buscar  
El sintonizador se detiene en el canal memorizado  
más bajo.  
Cuando se activa AUTOPROGRAMACION DE  
CA, donde no hay entrada de señal del televisor,  
aparecerá “NO HAY SEÑAL DE TV” en la pan-  
talla después de terminar la búsqueda de canales.  
El televisor/videograbadora puede reconocer los  
canales de TV para que sean canales de TV de  
antena de cable con las condiciones de recepción.  
En este caso, pruebe nuevamente con el prefijado  
automático en las condiciones de recepción fina.  
- 31 -  
ES  
 
LIMITED WARRANTY  
FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship as follows:  
DURATION:  
PARTS:  
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date of orig-  
inal retail purchase. Two (2) years for Picture Tube. This warranty does not cover any cosmetic parts or complete  
assembly parts.  
LABOR:  
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of original retail  
purchase.  
LIMITS AND EXCLUSIONS:  
This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail purchase will be  
required together with the product to obtain service under this warranty.  
This warranty shall not be extended to any other person or transferee.  
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or if service was  
attempted by an unauthorized service center. This FUNAI Limited warranty does not apply to any product not purchased and used in  
the United States.  
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It does not cover dam-  
age which occurs in shipment, or failures which are caused by repairs, alterations or product not supplied by FUNAI CORP., or dam-  
age which results from accident, misuse, abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance,  
commercial use such as hotel, rental or office use of this product or damage which results from fire, flood, lightning or other acts of  
God.  
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL), ANY  
COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.  
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL, INDI-  
RECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE INABILITY TO  
USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND  
OF ALL OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF  
MERCHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS  
REPRESENTATIVES IN THE UNITED STATES. ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED  
BYA FUNAI AUTHORIZED SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN OR DELIV-  
ERED TO A FUNAI AUTHORIZED SERVICE FACILITY.  
IMPORTANT:  
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS., YOU MAY HAVE OTHER RIGHTS THAT VARY  
FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN SATIS-  
FACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP. IN WRITING  
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION  
OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGE SO THE ABOVE LIMITATION OR EXCLUSIONS MAY  
NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER  
RIGHTS WHICH VARY FROM STATE TO STATE.  
ATTENTION:  
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT  
PRIOR NOTICE.  
To locate your nearest FUNAI Authorized Service Center or for general service procedure, please call 1-  
800-968-3429 or write to the following:  
FUNAI CORPORATION, INC. Service Center  
19900 Van Ness Avenue, Torrance, CA 90501  
Tel : 1-800-968-3429  
Printed in Malaysia  
1EMN20052  
★★★★★  
T5510UL  
 

Sony Computer Accessories SMP N100 User Manual
Sony CRT Television KV 24FV300 User Manual
Sony Home Theater System VGX XL2A User Manual
Sony Portable Speaker SS FCRW115 User Manual
Sony Radio XDR S55DAB User Manual
Speco Technologies Digital Camera HTD8FFI HTB11FFI HT7248FFI User Manual
Stanton CD Player C402 User Manual
StarTechcom Network Card usb to rs232 serial adapter User Manual
Swann Security Camera Maxi Brite Cam User Manual
Sylvania Flat Panel Television LC370SS9 User Manual